How many liters per second of water must the pump shown supply when the flow needed in the 915-mm diameter pipe is 1.314 cu.m./sec. Assume f=0.017 for all pipes.

Q: Assignment 4 For the system shown, What is the flow direction? b. What kind of machine is at A? c Do…

A: Given Data **As per our company policy we are supposed to do only 3 subpart if you need the rest…

Q: 2 in tube schedule 40 flow 24 in 4 in tube schedule 40 - 6 in water h

A: given; lets take pressure at A=PAlets take pressure at B=PB⇒diameter at A (dA)=4in=0.1016m⇒diameter…

Q: A pump is used to deliver 50 liters/sec at 120 rpm. If the rpm is increase to 140, determine the new…

A:

Q: The pump in figure 3 delivers water from the reservoir to the nozzle at the rate of 0.13 m/s. The…

A:

Q: Problem: Reservoir A has an elevation of 105 m. A pipe is connected from reservoir A to reservoir B.…

A: The overall pressure losses incurred by the fluid as it moves from the suction point to the…

Q: The difference in elevation between the source of the water supply and the centerline of the base…

A:

Q: Question 8 Describe the possible flows through the network of water pipes shown in figure where flow…

A: At each node, we write out the equation that represents the conservation offlow there. We then…

Q: If the flowrate passing through the apparatus is increased, what will happen to the corresponding…

A: The Bernoulli's equation for kinetic, potential and pressure head is given by, Pρg+v22g+z=c…

Q: Problem 10 Water flows steadily from an open tank as shown below. The elevation of point 1 is 10.0…

A: Given data: The elevation of point 1 is 10.0 m The elevation of points 2 and 3 is 2.00 m The…

Q: A pipe network consists of pipeline as shown. If the total rate of flow is 10 liters/sec, compute…

A: Total flow rate, Q1=10 liters/sec=0.010 m3/sd1=600 mm=0.6 mL1=3000 mC1=110d2=300 mm=0.3 mL2=2200…

Q: Calculate the discharge through the 140-mm diameter orifice shown. Assume C = 0.62.

A: Need to find the discharge through orifice.

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 50 mm diameter, subsequently…

A: Bernoulli's principle states that the flow energy of liquid before entering a section will be equal…

Q: What hp must be supplied to pump 2 cu. ft per sec from the lower to upper reservoir if the pump…

A: Flow rate, Q=2 ft3/secPump efficiency, η=75%Roughness of the pipe, e=0.003 ftElevation at lower…

Q: 3. A pump draws water at 300 liters per second from reservoir A and lifts it to reservoir B as…

A:

Q: pump is used to collect water from an underground tank. the tank water level is 5.44 meters below…

A: Given  Height of the pump from the tank water level (h) = 5.44 m flow rate () = 25.5 litres/second =…

Q: A fluid flows at 650 (ft^3)/min through the space between two concentric pipes. The inner pipe has…

A: Given: Q = 650 ft3 /min d = 1.5 in.  D = 4 in.    To find: Average velocity, uavg = ?

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 55 diameter, subsequently…

A:

Q: Determine the discharge, the velocity of flow and pressure at the point (2)?

A: Pipe diameter, d=6cm=0.06m

Q: A pump has a brake horsepower of 39 hp with an efficiency of 81%. Neglecting frictional losses,…

A:

Q: if the velocity of a liquid is 1.65 ft / s in a 12-inch diameter conduit. What is the velocity in a…

A:

Q: In a hydroelectric power plant, water flows through a large tube through the dam. This tube is…

A: In a hydropower plant, dams are used for transforming mechanical energy into electrical energy with…

Q: 2-the discharge through the pipe shown in fig. below is 0.4m'sec and the pressure head for point A…

A:

Q: Q5) Using a system similar to that shown in figure, compute the required air pressure above the…

A: Given data h1 = 0.3 mh2 = 5 mWe have to find the air pressure required to cause the jet to rise to…

Q: 4. Water enters a motor through a 600 mm diameter pipe under a pressure of 14 kPa. It leaves through…

A: Answer: The power supplied to the motor is 6.6351 kW.

Q: Q1- How much power must be supplied for the pump to maintain of 250mm of mercury vacuum and 275 Kpa…

A:

Q: Determine the pump head (unit: meter or kPa), using the following parameters

A:

Q: Determine the velocity in the 50-in. duct, in ft/s.

A: Use Of Ideal Gas Equation

Q: 6. Water enters a hydraulic reaction turbine with a velocity of 12 ft per sec and leaves it 3 ft…

A:

Q: Q1: If flow rate in pipe shown is (0.5m'/s) find the (H). H. water D=300 mm

A: Given data Volume flow rate = Q = 0.5 m3/sDiameter of pipe = 300 mm = 0.3 m

Q: A rotary pump draws oil from (tank 1) and delivers it into (tank2), the level in (tank 1) is 3 m…

A:

Q: Determine the number of stages needed for a centrifugal pump if it is used to deliver 420 gal per…

A:

Q: B-Draw the hydraulic gradient line and energy gradient line for the pipe system shown in figure…

A:

Q: A certain centrifugal pump can generate a head of H for a discharge of Q. If two of such pumps are…

A: This question is a very conceptual question of power plant. The topic which is covered is connection…

Q: A pipe with a radius of 9 mm is attached to a nozzle. If the velocity of flow in the pipe is 2 m/s,…

A:

Q: of 300 mm running at a speed of 2950 rev/min delivering 45 similar spare pump running at a speed of…

A:

Q: The pressure at the pump inlet in Psi, b) The pressure at the pump outlet in Psi, c) The total head…

A:

Q: Q1: If flow rate in pipe shown is (0.5m/s) find the (H). H. water D=300 mm

A:

Q: Water is flowing from A to B in a 4-in schedule 40 steel pipe. Point B is 6 m higher than point A…

A: Given,  Diameter of the Pipe , D = 4 inch  = 0.1016 m . Elevation of point B , above A , h = 6 m…

Q: Water enters through a 23.616 inches diameter pipe under a pressure of 14 kPa. It leaves through a…

A: Given data:-diameter at section 1-1, d1=23.616inches=0.6m⇒area of cross-section at section 1-1,…

Q: 4. A submersible pump delivers 350 gpm of water to a height of 5 ft from the ground. The pump was…

A:

Q: Given the problem: a.) Express a pressure gage reading of 35 psi in absolute pascals. Assuming Patm…

A: a) gauge pressure is given ,  P= 35psi  Patm=100 KPa

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A:

Q: Q1) Using a system similar to that shown in figure, compute the required air pressure above the…

A: Find the pressure in the tank.

Q: Determine the least number of stages for a multi-stage pump to deliver 80 L/s against a total head…

A:

Q: The motor of the pimp consumes 1.05 hp of electricity. The pump increases the pressure of water from…

A:

Q: The pump in figure 3 delivers water from the reservoir to the nozzle at the rate of 0.13 m/s. The…

A: Given The flow rate, Q = 0.13 m^3/s The head loss, h = 27.5 N.m/N The nozzle tip diameter, d = 0.074…

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1…

A:

Q: What power must be supplied by the pump to the flow if water (T =20°C) is pumped through the 300 mm…

A: Concept Of Fluid Mechanics Used

Q: A 3' diameter ppe flows full when it carries 30 cfs. find the discharge and depth in the pipe if the…

A: Given data: The diameter of pipe D0 =3ft Full flow rate Q=30 cfs The velocity of flow at any depth…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.