The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected by spur gearing. If one shaft runs at 1000 r.p.m. and the other at 2500 r.p.m., find the number of teeth on each wheel, if the module is 12 mm. Also detemine the exact distance apart of the shafts.

The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected by spur gearing. If one shaft runs at 1000 r.p.m. and the other at 2500 r.p.m., find the number of teeth on each wheel, if the module is 12 mm. Also detemine the exact distance apart of the shafts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts…

Q: The gear 'A' and gear B' are tried to transmit power from one shaft to another shaft. The gear 'A'…

A: Let us discuss about power transmission between shaft A and shaft B. Given data, Gear A, Tooth space…

Q: Determine the setting for a straight spur gear having 46 teeth of module 4 mm.

A: Given Data⇒ Straight spur gear : Number of teeth(t)=46 teeth Module(d)=4 mm

Q: A circular shaft with 50mm and its lenght is 850mm long and is made of steel, the shaft is subjected…

A: GIVEN :- diameter : d=50mm length: L=850 mm Torque subjected: T=800Nm (to determine θ we need the…

Q: The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The…

Q: 4)The tooth shape factor Y-. for helical gears should be determined by . В. cos B C. cos, D. cos² ß…

Q: h

A: Given

Q: 7.15 Two left-hand helical gears having the same helix angle are used to connect two shafts 60°…

A: (a) The number of teeth on gear: ZG = 62 teeth (b) The number of teeth on pinion: ZP = 25 teeth

Q: The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW…

Q: A pair of straight bevel gear consists of a pinion having 36 teeth and a gear having 88 teeth. If…

A: GIVEN DATA- Set of bevel gear given Gear teeth =88 pinion teeth = 36 Shaft angle =70' We have to…

Q: Q22: Assuming the diameter of shaft (2) is 30-mm, determine the rotation angle (in degrees) of gear…

Q: 1. Which of the following can be used for power transmission in intersecting shafts. a) Spur Gear b)…

A: As per our company guidelines we are supposed to answer only first 3 questions in case of multiple…

Q: In the arrangement of gears shown diagrammatically in Fig. 1, the driving shaft X runs at 1000…

Q: A gear train with a ratio of -6:1 and a diametral pitch of 8 is used to reduce the speed from an…

A: P

Q: 2- The four gears shown in the below Fig. are attached to a 50- mm diameter steel shaft. Compute the…

Q: Provide a very clear and complete solution. Determine the pitch diameter of a gear with 28 teeth…

A: Given Data m=2 Z=28

Q: In the coaxial gear train below, the speed of shaft Z is to be about but greater than 1/10th that of…

Q: odule of .05 inch, which rotates at 4000 rpm and has a pitch-line velocity of 15 ft/s. the second of…

Q: Which of following expression is correct for the determination of the 3 points efficiency for a worm…

A: Efficiency for a worm gear drive when worm is driving element:

Q: The set of double-reduction gears shown is driven by a pinion (Gear A) with a module of 1.5 mm,…

Q: 2. A pair of spur gear was fabricated with 2.5 mm/tooth module and to be mounted on shafts having a…

Q: 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total…

A: Given:Diameter of gear, d=220 mmpressure angle, ϕ=14.5oPower, P=50 kWSpeed, N=580 rpm

Q: 13–31 Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the…

A: Given N=1000 rev/min Power input 'H' = 75 KW module = 5mm pressure angle=20 degree

Q: Q2:- In an epicyclic gear train shown in the Fig. b, the i and E and the compound wheel C.D rotate…

Q: 4. For the extended epicyclic gear train shown. Gears 1, 3, and 6 have internal teeth while gears 2,…

A: In gear train , we knowvelocity ration=velocity of first drivervelocity of last driverBy using…

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

Q: The approximate distance between the two parallel shafts is 1500 mm. The shafts are to be connected…

Q: Determine the gear forces if Gear 1 is rotating at 600 rpm and transmitting 250 kW power. The module…

A: According to the details provided in the question, we need to find out forces the gear.

Q: The solid 25 mm diameter shaft is used to transmit torques applied to the gears. Use G= 80 GPa.…

A: Given: The diameter of shaft, d = 25 mm = 0.025 m The modulus of elasticity, G = 80 GPa

Q: The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected…

Q: 9.As for a gear mechanism, if the contact ratio ea=1.45, which means that while operating, there are…

A: Solution:

Q: The outside diameter of a hollow shat is 1.6 times the inside diameter. When transmitting 420 W of…

Q: 8.9 Two-spur wheels each have 30 teeth of involute shape. The circular pitch is 25 mm. and the…

Q: The axes of two parallel shafts are to be 600mm apart approximately, and have to be connected by…

A: given- centre distsnce of gear=600mm circular pitch =30…

Q: The approximate distance between the two parallel shafts is 1500 mm. The shafts are to be connected…

A: Given Data: Distance between the two parallel shafts (C.D)=1500 mm Speed of Gear NG=1500 rpm Speed…

Q: Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclock-…

A: Given module=5mm ϕ=20°M2=1000rpmCCWP=2πNT26075×103=2π×1000×T260T2=Torque on gear…

Q: aluminum shaft with a constant diameter of 60 mm is loaded by torques applied to gears attached to…

Q: The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: Problem 3 The gear system shown below has a motor supplying 38 kW at 340 rpm to gear A. Assume the…

A: Given, Power supplied by motor = P = 38 kW = 38,000 W Rotational speed of gear A = NA = 340 rpm…

Q: An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached…

Q: (b) An internal wheel B with 90 teeth is keyed to a shaft F. A fixed internal wheel C with_ teeth is…

Q: other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine…

Q: In a spur gear arrangement, the driver has 70 teeth of 26 mm pitch. Find the power, if it can…

Q: HW8 Two parallel shafts, about 200 mm apart are to be connected by spur gears. One shaft is to run…

A: Givenx=200 mmN1=360 rpmN2=120 rpmNow letd1=Pitch circle diameter of gear 1d2=Pitch circle diameter…

Q: 3. The center distance of two pair of meshing spur gears 4 = a, =160mm m, = m, z, = 20. 3 = 30, 2, =…

A: As per given question Given a1=a2=160mm M1=M2 Z2=20 Z3=30 Z4=50 We have to determine number tooth…

Q: Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts…

A: Given data distance between the shafts = 600 mm one shaft runs at= 1000 r.p.m. other shaft at =…

Q: Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh.…

Q: Q5: Select A suitable spline having a fit B for a gear to be mounted on a shaft with a diameter D=…

A: T=2.3×106 N-mmd=60 mm l=100 mm And for steel σyc =σyt=400 Mpa so τper=σycor σyt2=200 Mpa

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

HW12
The approximate distance between the two parallel shafts is 600 mm. The shafts
are to be connected by spur gearing. If one shaft runs at 1000 r.p.m. and the other
at 2500 r.p.m., find the number of teeth on each wheel, if the module is 12 mm.
Also detemine the exact distance apart of the shafts.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

. Determine the angle of twist for the steel (AISI 4340, OQT 1200 F) hollow shaft with anoutside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kWof power at a speed of 45 rad/sec. The shaft length is 400 mm
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion with 15 teeth. The overall ratio of the gearbox is 6:1 and the gearbox is transmitting a power of 6000W. If the factor of safetv is to be reduced to an absolute minimum acceptable value and the gears are to be made from a material with a Yield stress of 540 MPa, what is the face width of the gears (in mm) Express your answer in the form 21.00 ie with two decimal place an no units
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
The motor shown in Fig. P6-47 develops 100 hp at a speed of 360 rpm. Gears A and B deliver 40 hp and 60 hp, respectively, to operating units in a factory. If the maximum shearing stress in the shafts must be limited to 12 ksi, determine a. The minimum satisfactory diameter for the motor shaft. b. The minimum satisfactory diameter for the power shaft. (1 hp=745,7 watts); (1 ksi=6,89 MPa); (1 ft=0,30 m)
A pair of 20º full depth involute teeth bevel gears connect two shafts at right angles having velocity ratio 3 : 1. The gear is made of cast iron having allowable static stress as 70 MPa and the 20teeth pinion is of steel with allowable static stress as 100 MPa and 200BHN. The pinion works at 750 r.p.m. Determine the maximum power can be transmitted by the gears if the module is 10mm. Kf=1.4
I n a reverted gear train, as shown in Fig. Q2, two shafts A and B are in the same straight line andare geared together through an intermediate parallel shaft C. The gears connecting the shafts Aand C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm.The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio ateach reduction is same. Find suitable number of teeth for all gears. The number of teeth of eachgear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance ofshaft C from A and B
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6 m. length when subjected to a torque of 14 kN-m? Use G = 83 kN/ m2. Convert your answers to mm. Based on the problem above, what is the maximum shearing stress developed? Use G = 83 kN/ m2. Convert your answers to MPa.
The shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 25 kN·m is applied to gear B. Both shafts have the same diameter of 100 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.)
What is the minimum diameter of a solid steel shaft that will not twist through more than 4o in a 9 m length when subjected to a torque of 11 kN.m ? if G = 83 GPa
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° (degrees) in a 6 m. length when subjected to a torque of 14 kN-m? Use G = 83 kN/ m^2. Convert your answers to mm.