The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The driving sprocket has 10 teeth. Find the number of teeth on the driven sprocket. If the pitch radius of the driven sprocket is 250 mm and the center-to-center distance between the two sprocket is 400 mm, find the pitch and length of the chain. [Ans. 30 ; 52.25 mm ; 1.93 m]

The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The driving sprocket has 10 teeth. Find the number of teeth on the driven sprocket. If the pitch radius of the driven sprocket is 250 mm and the center-to-center distance between the two sprocket is 400 mm, find the pitch and length of the chain. [Ans. 30 ; 52.25 mm ; 1.93 m]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a chain drive, the speed of the chain is not uniform and varies from a minimum value to a maximum value for every rotation or cycle of tooth engagement. If the ratio of the maximum value of the chain speed to its minimum value is 1.017322, determine the angle of articulation in degrees.
A chain with speed of 900 fpm has driving sprocket turns at 1000 rpm. If the pitch of chain is 3/4-in, find the number of teeth of driving sprocket. (Ans. 14 teeth)
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 35cm respectively. If driven shaft runs with 8 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 5mm
In a brick-making machine is found this train of gears. A motor carrying pulley E, which is 8 in. in diameter, drives the machine. The wide-faced roller F, 14 in. in diameter, drives a conveyor belt. If the motor runs at 1500 rpm. what is the speed of the conveyor belt in ft. per minute? (Neglect the thickness of the belt).
. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axes are at 60o to each other. Produce a graph of velocity ratio against angle for f to proof the calculated results.
A roller chain and sprocket is to drive vertical centrifugal discharge bucket elevator with a center distance of 70.82 inches. The pitch of chain connecting sprockets is 1.75”. The driving sprocket is rotating at 217 rpm and has 11 teeth while the driven sprocket is rotating at 38 rpm. Determine (a) the number of teeth of driven sprocket and (b) the chain length in pitches, and (c) the chain length in inches.
Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth numbers of gears z4: 77 The efficiency of gear pairs ηd: 0,96 The efficiency of the bearing pairs ηr: 0,94 Electric motor speed: 2050 Belt speed (v) (m / s): 1.30 Required force for belt movement (N) g: 2200 a) Find the diameter of the drum? b) Find the required motor power?
Plate gear C of this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as the sun wheel B for every five revolutions of the driving spindle carrying the sunwheel B.Determine suitable number of teeth for all the wheels and the exact diameter of pitch circle of the ring.1.1.Calculate the number of teeth of the ring gear D.(3)1.2.State an equation tha relate the number of teeth of gear D, B and C.(1)1.3.Use the table method to calculate the number of teeth of gear B.(13)1.4.Calculate the number of teeth for gear C.
Original Question: The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B QUESTION THAT NEEDS TO BE ANSWERED: For the bevel gear system shown in problem above, determine the angular accelera-tion of gear B when gear A is stationary and member OC has an angular velocityof 10j rad/sec and and angular acceleration of 25j rad/sec2
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.