HW2.1- Find the values in the circuit if the current through the 36Q resistor is Is =5,4 A. Determine:(a) Vr3R2 62(b) Vr+ Vg2(c) I50R4 150R3(d) Pi (R1)(e) Pr (V,)30Ω Ri5,4A||1,R53362R6 12Ω

Answered: Image /qna-images/answer/b8a19db0-a85e-4dfa-afef-17aea020155d.jpg

HW2.1- Find the values in the circuit if the current through the 36Q resistor is Is = 5,4 A. Determine: (a) Vr3 R2 60 (b) Vr + Vra (c) I R4152 R3 (d) Pi (R1) (c) Pr (V,) 300RI 5,4 A||1, R53362 R6 122 3V

HW2.1- Find the values in the circuit if the current through the 36Q resistor is Is = 5,4 A. Determine: (a) Vr3 R2 60 (b) Vr + Vra (c) I R4152 R3 (d) Pi (R1) (c) Pr (V,) 300RI 5,4 A||1, R53362 R6 122 3V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.What factor(s) can contribute to differences between ideal theoretical values in a circuit and values measured in actual practice? A) Measurement inaccuracy B)Component tolerances C)Both (a) and (b). D)Neither (a) nor (b). 2.What maximum range of values could resistor R3 have and still be within tolerance assuming R3 is a 10% resistor? A) 3296.7 – 3303.3 Ω B) 2970 – 3630 Ω C) 3267 – 3333 Ω D) 2967 – 3633 Ω 3.A voltage of one volt applied across a resistance of one ohm produces a current of one ampere. What happens to the current if the voltage is doubled and the resistance is halve? A)It doubles. B)It increases four times. C)It increases three times. D)It remains the same. In Question 3, what is the current in amperes if the voltage is halved and the resistance is doubled? A) 1 ampere B) 33 ampere C) 5 ampere D) 25 ampere
Using Kirchhoff's Rules, compute the current (mA) and voltage (V) values of the circuit if R1=2kΩ and R2=7kΩ.
Given the electrical circuit of the image:The value of the current passing through L2 is equal to zero (0).Answer the following questions:– 1. Is it possible to find an equivalent Thevenin resistance for L1? If so, list the steps to find it.– 2. Explain step by step, how would you find the value of the voltage v2, if we do not know the value of the current that passes through L1?– 3. What is the value of voltage v2, if the current passing through L1 is i(t) = 0.5 sin (60t – 90°)?
Consider the circuit diagram below. Given I = 2.5 mA and Is = 1.25 mA: a) Find the currents Is2, I2, I3, I4 and Iz. State your conclusion as a table of values. b) What is the voltage drop across R7? c) If Vab = 2.75 V, what is the value of Rs?
As with the nodal analysis, the analysis of meshes for an electrical circuit is quite advantageous. This is because it also, to be developed, does not need a high number of equations. In practice, the main objective of this technique is to search for the intensities of called mesh currents. This is what can be done in the circuit presented below. Case the analysis of its meshes is carried out on it, what will be the current intensities found?
1. In a circuit that contains only resistors in series, the current is the same throughout the circuit (remember that current is conserved!). The amount of current in the circuit is determined by the potential difference (or em f) of the battery and the equivalent resistance, Req, of the circuit. We can therefore write Ohm's Law as DeltaV = IReq. Assume the batteries supply a potential difference of DeltaV = 3.0 V, and use the currents measured in circuits 3a, 3b, and 3c to determine the equivalent resistance in each circuit. Please show the calculation of each. R1 = 150 ohm, R2 = 230 ohm R3 = 270 ohms (don't believe question should need these but providing anyways) Current MeasuredCurrent through R1 in 3a (Only resistor 1) Ir1= 0.01 amp Current through R1 in 3b (Resistor 1 and 2) Ir1= 0.0032 amp Current through R1 in 3c (Resistor 1, 2 and 3) Ir1 = 0.002 amp
Nodal analysis is another very useful way to obtain information regarding a circuit.electric. For example, consider the 4 Ω resistor in the circuit shown below. Nodal tension to your left was named V1, while the right was named V2. Therefore, determine the values of these tensions. answer:v1 = 9,43 V ; v2 = 11,15 V
Using the following values for the circuit in the figure, find what is required in the questions? For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=9.12 kΩ VG=? VGS=? ID=?
Answer the following if V1=8V, R1=9 Ω, R2=3 Ω, R3=4 Ω, R4=7 Ω and I1=10 A in the circuit in the figure i1=? Pv1=? PI1=? P5i1=?
Using the two images attached of a Circuit State What is the Circuit doing and Give an example of a real life application where it can be used V1= 6v V2 = 2V
Construct this circuit using the simulation: (simulation link: https://phet.colorado.edu/sims/html/circuit-construction-kit-dc/latest/circuit-construction-kit-dc_en.html ) Let: R1 = 2000 ohms R2 = 5000 ohms R3 = 3000 ohms R4 = 1000 ohms V1=24V 1. Total equivalent resistance of the circuit (using theoretical calculation) 2. Total current on the circuit (using simulation) 3. Total equivalent resistance of the circuit (using simulation) 4. % Error of #1 and #3 question.
Consider the following circuit: If I1 = 14 A, I2 = 4 A, V1 = 6 V, R1 = 7 Ω, R2 = 18 Ω, RL = 10 Ω, how much is the contribution of I1 to the voltage vx?