I a) Calculate the temperature of the high temperature reservoir in K if the low temperature reservoir is held at 300K. --> enter the answer in the box below. [b) Write down the adiabatic process paths during this cycle. (1-2 or 2-3 or 3-4 or 4-1) [ c) Calculate the heat addedQ_H from the high temperature reservoir into the Carnot cycle [d) Calculate the net work output of this cycle.

I a) Calculate the temperature of the high temperature reservoir in K if the low temperature reservoir is held at 300K. --> enter the answer in the box below. [b) Write down the adiabatic process paths during this cycle. (1-2 or 2-3 or 3-4 or 4-1) [ c) Calculate the heat addedQ_H from the high temperature reservoir into the Carnot cycle [d) Calculate the net work output of this cycle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When 1 kg of coal is burned in the boiler, 10 m3 of exhaust gas is formed, the volume ratios of which are given below. With 220 C from the chimney If the exhaust gas released is reduced to 20 C, find the heat to be saved from each kg of coal according to the method you want? H20 4.55% ; 02 6.71%; CO2 11.83%; N2 76.9% and for all gases V=22.4 m3
A fluid at [X] bar occupying [Y] m3 is compressed reversibly to a pressure of [Z] bar and specific volume of [A] m3/kg according to the law pvn = c. The fluid then expands reversibly according to the law pv2 = c to [B] bar. A reversible cooling at constant volume then restores the fluid back to initial state. sketch the P-v diagram for the cycle in the calculation evidence submission. Did you include the sketch in the calculation evidence submission?
(1.3) Suppose a process increases Gibbs free energy of a system coupled to both a heat bath and volume reservoir, i.e., AG > 0. What does that tell you about the system's coupling to work reservoirs? Explain. Answer:
THERMOFLUID Consider a gas undergoing a thermodynamic cycle consisting of three processes from an initial state at P1 = 100 kPa , V1 = 0.81 m3. Process 1 - 2 : constant pressure compression work of 65 kJ,Process 2 – 3 : constant volume heating of 2600 kJ, andProcess 3 – 1 : isothermal expansion. a) Sketch the cycle on a clearly labelled P-V diagram and write appropriate First Law equations for all the three processes. Neglect the changes in kinetic energy and potential energy.
THERMOFLUID Consider a gas undergoing a thermodynamic cycle consisting of three processes from an initial state at P1 = 100 kPa , V1 = 0.81 m3.Process 1 - 2 : constant pressure compression work of 65 kJ,Process 2 – 3 : constant volume heating of 2600 kJ, andProcess 3 – 1 : isothermal expansion. a) Sketch the cycle on a clearly labelled P-V diagram and write appropriate First Law equations for all the three processes. Neglect the changes in kinetic energy and potential energy. b) Determine the:i. volume at the end of constant pressure compression, ii. net work for the thermodynamic cycle, and iii. heat transfer during constant pressure compression.
Relate between the entropy with the Clausius statement of the second thermodynamics law. [Note: The answer must include appropriate equations]
(Topic: Carnot cycle) Two and a half kg of an ideal gas with R = 296.9 J/(kg)(K) and cv = 0.7442 KJ/(kg)(K) at a pressure of 827.4 kPa and a temperature of 667 ̊C reject 132.2 kJ of heat at constant pressure. The gas is then expanded according to pV1.25 = C to a point where a constant volume process will bring the gas back to its original state. Determine P3 , QA , and the power in kW for 100 Hz.
Shown in the figure below is the cycle undergone by a Heat Pump. Your heat pump runs using 38.55 moles of monatomic Helium gas. At point a in the figure, the temperature is T₂ = 321 Kelvin and the pressure is Pa = 216000 Pascals. During the process a→b, the Volume of the system Quadruples. P Cv= Cp Y = C с a STATE a b isothermal P (Pa) b V Joules/(mole. K); Joules/(mole K); V (m³) T (K) PROCESS W (J) a-b b-c c-a Total Qhot = Qcold = Performance Coefficient = Joules; Joules; Q (J) AU (J) Activate Windows Go to Settings to activate Window
In one cycle, a heat engine absorbs 1.71 kJ from a hot reservoir at 277°C and expels 1.18 kJ to a cold reservoir at 27°C. (a) What is the engine's thermal efficiency (in percent)? % (b) How much work is done by the engine (in J) in each cycle? (c) What is the engine's power output (in kW) if each cycle lasts 0.302 s? kW Need Help? Read It
2. The work required to compress a gas reversibly according to pV130 = C is 67,790 J, if there is no flow. Determine AU (in kJ) and Q (in kJ) if the gas is methane. For methane, k = 1.321, R = 518.45 J/kg-K, cv = 1.6187, cp = 2.1377 J/kg-K please draw the P-V and T-S diagrams
4. One kg of water at 47.8° C is heated under a constant pressure of 14 bar until it is converted into steam with 110° C of superheat. Determine the quantity of heat supplied during superheating and the total heat of superheated steam. Assume c, = 2.1 kJ/kg K. [Ans. 201 kJ: 2818 kJ] certain amount of team ir pro feration 08 Dw
Q1) Steam is supplied to a turbine at 30 bar and 350°C. The turbine exhaust pressure is 0.08 bar. The main condensate is heated regeneratively in two stages by steam bled from the turbine at 5 bar and 1.0 bar respectively. Calculate masses of steam bled off at each pressure per kg of steam entering the turbine and the theoretical thermal efficiency of the сycle. 1 kg Turbine 1- m- m2 0 1- m, 1- m,-m2 m. h, m2. h2 Condenser 1 kg twwww www meel 1 kg Heater-1 Drain cooler m, m,+ m2 (Н.P.) Heater-2 (L.P.)