Determine the stopping temperature and stopping pressure forthe following substances and flow conditions flowing in achannelA) 0.15 MPa pressure, 50 OC temperature and 300 m/ s speedheliumB) 0.15 MPa pressure, 50 0C temperature and 300 m / s speednitrogenC) 2.0 MPa pressure,Water vapor at a temperature of 350 0Cand a speed of 480 m /s

(A) Given Data Temperature of helium is : T=50°C Pressure of helium is : P=0.15 MPa Velocity of…

Determine the stopping temperature and stopping pressure for the following substances and flow conditions flowing in a channel A) 0.15 MPa pressure, 50 0C temperature and 300 m / s speed helium B) 0.15 MPa pressure, 50 0C temperature and 300 m/s speed nitrogen C) 2.0 MPa pressure,Water vapor at a temperature of 350 OC and a speed of 480 m / s

Determine the stopping temperature and stopping pressure for the following substances and flow conditions flowing in a channel A) 0.15 MPa pressure, 50 0C temperature and 300 m / s speed helium B) 0.15 MPa pressure, 50 0C temperature and 300 m/s speed nitrogen C) 2.0 MPa pressure,Water vapor at a temperature of 350 OC and a speed of 480 m / s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

After graduation, you work for a pump manufacturing company. One of your company’s best-selling products is a water pump, which we shall call pump A. Its impeller diameter is DA = 6.0 cm, and its performance data when operating at n. A = 1725 rpm (?A = 180.6 rad/s) are shown in Table.The marketing research department is recommending that the company design a new product, namely, a larger pump (which we shall call pump B) that will be used to pump liquid refrigerant R-134a at room temperature. The pump is to be designed such that its best efficiency point occurs as close as possible to a volume flow rate of V. B = 2400 cm3 /s and at a net head of HB = 450 cm (of R-134a). The chief engineer (your boss) tells you to perform some preliminary analyses using pump scaling laws to determine if a geometrically scaled-up pump could be designed and built to meet the given requirements. (a) Plot the performance curves of pump A in both dimensional and dimensionless form, and identify the best…
Water flows through a 125 mm diameter pipe at a velocity of 7.5 m/sec. Find the mass flow rate in kg/sec. NOTE: Do not write any unit to your answer, put your answer in a numerical form only and use up to 3 decimal places. ASAP PLS
5. Write down the Benoulli equation and explain the meaning of each terins 6. Water is flowing through a hole at the bottom of large tank filled with water. Tank is open to atmosphere. The level of water in the tank is 20 m Calculate velocity of flow. Assume steady flow and neglect viscous effects. 20 m 2 Tig.1 F. 1.0 P-100 kPa Handwriting not allow please
A certain hydropower plant is being supplied by river flow of 900 cubic ft/sec and the head on the site is 200 ft. To develop maximum capacity it was proposed to install 2 turbines, one of which is 1.5 times the capacity of the other. Both turbine units are assumed to have efficiency of 85%. Determine (a) the total power developed, (b) what is the power developed by turbine #1 and by turbine #2 and (c) Rotative speed of each turbine unit assuming specific speed equal to 70 rpm.
Convert the following inappropriate quantities into SIunits: ( a ) 2.283 E7 U.S. gallons per day; ( b ) 4.5 furlongs perminute (racehorse speed); and ( c ) 72,800 avoirdupoisounces per acre.
Guava juice enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft3 / hr, then exits through a d of 6.4 in. Calculate the velocity at the exit?
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
A water jet has a diameter of 75mm and ahs a velocity of 15m/s. What is the horsepower exerted by the jet. ANSWER: 10hp
a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump efficiency is 66%
A two floor building has two faucets, one in the basement and one in the first floor. The maximum water (\rho = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 12m/s. The faucet diameter is 1.5 cm. Neglect all losses. (a) How much is the maximum velocity at the first floor faucet, when the basement faucet is closed? (b) What would be a maximum height (from the basement floor) for a faucet, to still get a maximum exit velocity of 5 m/s?
I get a little confused when it is stated "Flow rate is = Ma" Isnt flow rate= Av?
Wind energy question #1 Q1) Wind at 1 standard atmospheric pressure and 15°C temperature has a velocity of 5 m/sec what the total power density in the wind stream? Choose the correct answer (76 w/m?, 15.25 w/m?, 3 w/m?) Q2) A. The anemometer is advice to measure the always recommended to set up on the height of B. The maximum power from wind power from wind stream by wind rotor is Itcal ......... Coefficient C. Savonius rotor s classify as ............. wind turbine Q3) How wind turbine classified ? Discuss with brief. Q4) Write short notes on applications of wind energy. Wind energy question #2 Q1) 1. If the mechanical and electrical efficiency about 70% and with consideration of Betz coefficient the total out power from wind power system . 2. Darrieus rotor is consider as . axies wind turbine, 3. The wind speed measure by the............. which recommended to set up on m height. Q2) What the power density in the wind stream of standard atmospheric pressure and 19°C temperature has a…