I am unsure of how to solve these and if my solution is correct.

Q: Why is the answer in the question different from that of the solution?

A: At point A, oil is present sp gravity of oil = 0.92  (given) density = specific gravity × 1000…

Q: A hydraulic press has a plunger diameter 4.5 cm. The force acting on the ram and plunger are 22.22…

A: Write the given values along with the suitable variables.

Q: 3- Comparing the theoretical results and calculations with the process and discussing the…

A:

Q: 200 kN 40 kN/m z (m) 1 2.5

A: "Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Analyze if shafts subjected to pure torsion can be made hollow, explain and if so, they would have…

A:

Q: ables shown below. Patm h.

A: given:

Q: is driven by a 4 kW motor. The moment of inertia of the rotating parts of the machine is equivalent…

A:

Q: The general solution to an IVP isy = k exp(-2t)+1. Find the value of k needed for it to satisfy the…

A:

Q: Water is poured at a constant rate into a tank having a square base of side 6m. The mass of water in…

A: Given data, m˙ = 375 kg/sec ρ = 1000 kg/m3    we know that Density = massvolume ρ = m˙V

Q: Answer the second problem Only

A: To draw SFD and BMD

Q: Please show the complete solution. Help me to answer the table

A: L=6.0 cm=0.06 mho=4.7 cmh1=5.0 cmH=ho+h1-h

Q: * It equal and opposite forces applied to a body tend toelongate it, the stress so produced is…

A: The correct answer is TENSILE STRESS TENSILE STRESS: when equal and opposite forces act on a body…

Q: It equal and opposite forces applied to a body tend toelongate it, the stress so produced is called…

A: To select the correct option.

Q: e) lost work for non-flow process f) lost work for steady flow process

A: In this problem, it is asking about the answers of parts e and f. so we will answer parts e and f.

Q: Explain volumetric efficiency and cite any three factors that affect it

A: The volumetric efficiency and three factor affecting is given.

Q: . How much work is done in forcing 50 ft3 of water through a 0.5-inch pipe if the difference in…

A:

Q: Measure the outside diameter of a flagpole or a street-light pole by first wrapping a piece of…

A: Measure the outside diameter of the street-light pole at the bottom using a string by measuring the…

Q: 2. A cylindrical container having cross-section area 100.0 m², which is put on the ground, is filled…

A: The unit of speed is “m/s” not “m/s2”. So in this solution unit of speed taken as “m/s”. Given data:

Q: I needed it to be solved using differential equation

A:

Q: this problem can be solved. a truck got big load. about 2000 kg. cylinderBC. find the force on A.…

A:

Q: Solve for the pressure differential in Pa if the temperature inside a 5.14m vertical wall is…

A: Calculate the pressure difference on the bottom of wall at the left and right wall

Q: . Р D 6 ft A B, 8 ft

A: For solution refer below images.

Q: The cylinder in Fig . 2-11 is used to raise the weight 9 in. If the bore of the cylinder is 21/2 in.…

A:

Q: ery quickly to solve this que

A:

Q: List types of work done that exist in the system as shown in Figure 2, below and justify your…

A:

Q: A pneumatic system is producing 120lb/in^2 of gauge pressure. It has been determined that 7 lb of…

A:

Q: T1= 50c , T2= 54c , P1=2.5 bar , P2= 143 bar Find n??

A:

Q: The open cylindrical tank is filled with linseed oil. A crack having a length of 45 mm and average…

A:

Q: with Diameter of 3 in Cove a and Length of 7 in, with wet weight lbf of 3.44 and porosity of 0.172.…

A:

Q: The cylinder and tubing shown in Fig. 2-26 contain oil, sp gr 0.902. For a gage reading of 31.2 psi,…

A: Given , Gauge reading , Pg = 31.2 psi =31.2*144 lbs/ft2 =4492.8 lbs/ft2. Specific gravity of oil  =…

Q: How can I find the solution

A: Write the Bernoulli expression as follows.

Q: ᴛʜᴇ ᴅᴇɴꜱɪᴛʏ ᴏꜰ ᴛʜᴇ ꜰᴏʟʟᴏᴡɪɴɢ ᴘᴜʀᴇ ᴍᴇᴛᴀʟꜱ, ᴇxᴘʀᴇꜱꜱ ʏᴏᴜʀ ᴀɴꜱᴡᴇʀ ɪɴ ᴋɢ/ᴍ^3. (Show solution in manner)…

A:

Q: )Convert 65 lbm to Ibf in Engineering System.Assume 32.174 ft Answer using proper significant…

A:

Q: 5 kN 1m 2m E 2 m 3 kN D B 2 m

A: GIVEN DATA- A PLANE TRUSS GIVEN  WE HAVE TO FIND FORCE IN MEMBER BC

Q: A machinist wishes to insert a brass rod with a diameter of 3 mm into a hole with a diameter of…

A:

Q: hm1 hi hm2

A:

Q: Thevenin theorem?

A: Thevenin's Theorem states that “Any linear circuit containing several voltages and resistances…

Q: 1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:

A: Given  Ultimate strength = 1600 Mpa

Q: solution! Given: FN = 52 MN = 100 SN = 75

A: As per policy I can answer only first question. Please ask second question as new

Q: magnitude of W so th

A: Given: To determine: weight of wheel 1, W

Q: What is the theoretical horsepower requirement of a bucket elevator that is loaded down side with…

A:

Q: omplete informations to s

A: given:

Q: A very large cyndrical shaped tank has a radius of 4 feet and a height of 15 feet. The tank is…

A: Given               radius = 4 feet               height = 15 feet weight density = 48 pounds per…