A hydraulic press has a plunger diameter 4.5 cm. The force acting on the ram and plunger are 22.22 KN and 500 N respectively. Find the diameter of ram in centimetres. If the diameter of the plunger is changed to 2.5 cm for the same force on plunger and ram, then find the diameter of ram. Analyse the which law is applicable in this problem and discuss.

A hydraulic press has a plunger diameter 4.5 cm. The force acting on the ram and plunger are 22.22 KN and 500 N respectively. Find the diameter of ram in centimetres. If the diameter of the plunger is changed to 2.5 cm for the same force on plunger and ram, then find the diameter of ram. Analyse the which law is applicable in this problem and discuss.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1PSI = 6897.1 Pa
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?
A hydraulic cylinder filled with water has an inside diameter of 1.0 in and a length of 2.0 ft. How many pounds of force must be applied to a piston at the end of the cylinder to compress the water by 0.1 in? Take the bulk modulus of water to be K=312,000 psi.
Q6: A hydraulic lift is to be used to lift a 2500 kg weight by putting a weight of 25 kg on a piston with a diameter of 10 cm. Determine the diameter of the piston on which the weight is to be placed.
a force is 1.6 kN is applied uniformly on piston of 8 cm diameter. determine the pressure on the piston.
Find the force applied by support BC to the gate AB. The width of the gate and support is 3 m and the weight of the gate is 1500 N.
The diameters of a small piston and a large piston of hydraulic jack are 2 cm and 10 cm respectively. A force of 60 N is applied in the small piston. Find the load lifted in N by the large piston when the piston are on the same level.Take density of the liquid in the jack is 1000 kg/m^3.
An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, and if it slides down a frictionless plane that is inclined at 300 with the horizontal, determine the angle the free surface makes with the horizontal. Ans. The free surface is the same as the angle.
A hydraulic press has a ram of 30 cm diameter and a plunger of 2cm diameter. it is used for lifting a weight of 30 kN. How much force is required at the plunger? a) 155.5kN b)466.6kN c) 311.1 kN d) 233.3 kN