I have ten-ohms resistors available to connect and arrange in a series or parallel or in a combo of series and parallel. If I need the resistance to be 35 ohms, how many of the ten resistors do I need to use? What does the configuration look like?

I have ten-ohms resistors available to connect and arrange in a series or parallel or in a combo of series and parallel. If I need the resistance to be 35 ohms, how many of the ten resistors do I need to use? What does the configuration look like?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 19PQ

See similar textbooks

Related questions

Q: How can I combine 2 kQ resistors and one 4kQ resistor so that I end up with a resistance less than…

Q: What is the smallest possible resistance you can get by connecting a 40 Ohm, 60 Ohm, and 120 Ohm…

A: The smallest possible resistance will be obtained when the three resistors are connected in…

Q: You need a 45 resistor, but the stockroom has only 20 2 and 50 resistors. How can the desired…

Q: You have a collection of 1.0 kΩ resistors. How can you connect four of them to produce an equivalent…

Q: Four resisters, 10 ohms, 14 ohms, 27 ohms, and 33 ohms are in a series. How do you find the…

A: In series combination current in all the resistors will be same. In series combination the…

Q: You need an RC combination for a digital timer that will allow a capacitor to charge to 75% of its…

Q: How do you find the value of a resistance R1, in a circuit when the equivalent resistance is 40…

A: R2 = 12 Ω R3 = 40 Ω R4 = 20 Ω To find = R1 and current across each resistor

Q: 30 W 60 W B AV

Q: Can any arbitrary combination of resistors be broken down into series and parallel combinations? See…

A: No, the arbitrary combination of resistors cannot be broken down into the series and the parallel…

Q: Suppose the series resistors in the example are now 4.00 N and 2.00 N while the parallel resistors…

Q: Given the following combination of resistors below: If the total resistance of the combination…

Q: What value of a single resistor (in Ω) would be equivalent to that of the resistors in this…

Q: If there is 60 v across a 680 ohm resistor, what is the power?

A: Given data: Voltage (V) = 60 V Resistance (R) = 680 Ω Required: Power (P)

Q: 200 Ω resistor and a 500 Ω resistor are in series as a part of a larger circuit. If the voltage…

A: 200 Ω resistor and a 500 Ω resistor are in series as a part of a larger circuit. If the voltage…

Q: hat resistance do you need to connect in parallel to a 125 Ω resistor to get a total of 49.0 Ω?…

A: 1Rnet=1R1+1R2

Q: Two resistors R, and R2 are wired as shown in the figure. Calculate the electric power for R2, given…

Q: Find the equivalent resistance of the combination of resistors shown in the figure below. (R1 = 2.12…

A: The equivalent resistance when two resistors R1,R2 are connected in series is given by, Rs=R1+R2 The…

Q: Suppose you are doing a physics lab that asks you to put a resistor into a circuit, but all the…

Q: You measure the power delivered by a battery to be 6.00 W when it is connected in series with two…

Q: Three 100-Q resistors are connected as shown in 100 Q Figure. The maximum power that can safely be…

Q: How many 0.5W resistors, each of the same resistance, must be used to produce an equivaler 3.0 kN ,…

A: Given:- The power of the single resistor = 0.5 W The total equivalent resistor is 3 KΩ= 3000 Ω…

Q: Ritche The potential difference across a 100 ohm resistor is 4.0 volts . What is the power…

A: All three resistance connect in parallel

Q: What is the minimum number of 8 Ω resistors arranged in series that would be necessary to keep the…

Q: The total resistance of 21.0 Ω is to be produced by connecting an unknown resistance to a 22.0 Ω…

Q: You have a battery of 960 V and four resistors each with a resistance e of 40 Ohms. If you make a…

Q: An airplane black box contains a bunch of unknown resistances and batteries connected in unknown way…

A: Given Data:- R1= 9Ω resistor draws a current i1=0.80 A and R2=17 Ω resistor draws a current i2=0.50…

Q: You have three resistors, each with a resistance of 5 Ω. How would you connect them to obtain (a)…

A: Given, three resistance having resistor, R = 5 Ω

Q: What is Voltage associated with 0.07 amps passing through a 87 resistor?

Q: R2 R4 R1 R3

A: R1 = 22.2 ohm R2 = 52.2 ohm R3 = 140 ohm R4 = 84 ohm Emf of the battery = 24 Volts

Q: Find the unknown values of voltage and current in each resistor as shown in the given circuit…

Q: You are given a number of 34 resistors, each capable of dissipating only 3.5 W without being…

Q: In a given physics lab, you are asked to build a circuit with a resistance of 100 Ohms, but all you…

Q: If 12- V battery supplies 1.90 A to a 2.74 resistor. What is its internal resistance ?

A: Given data: Battery emf (E) = 12 V Current (I) = 1.90 A Resistance (R) = 2.74 Ω Required: Internal…

Q: A 200-2 resistor and a 500-2 resistor are in series as a part of a larger circuit. If the voltage…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: с Consider the circuits shown below. What is the current through each resistor? R = 2 k2 %3D EV, 1.6…

Q: What happens to the current when a 10-V battery is used to power a 10-ohms resistor? Why will this…

A: Given: Potential, V=10 V Resistance, R=10 ohms Formula: OHM'S LAW: V=IR Current can be found using…

Q: Hi, here's my question. 26.61: Find the current through each of the resistors of the circuit shown…

A: Let I1 is the current through the 2ohm resistor, I2 is the current through the 5ohm resistor and I3…

Q: Question 25 V, 15 V A' 6 v V,) 30 R. 42 (V. In the circuit diagram above with switch S closed, the =…

A: ⇒“Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: QUESTION 1 Calculate the lowest power delivered on a resistor of showing Figure. All resistors have…

A: Power delivered on a resistor is given by: P=I2R Ohm's law states that the current flowing through a…

Q: If you were to place a 3kΩ resistor across a 9 volt battery, what is the power dissipated from this…

A: Given data: Resistance (R) = 3 kΩ = 3000 Ω Battery (V) = 9 V Required: Power (P)

Q: 6. A 8.00 µF capacitor is connected in series to a 120-V battery, a 550-2 resistor, and a switch.…

Q: You need a 45 Q resistor, but the stockroom has only 20 Q and 50 Q resistors. How can the desired…

Q: If you have two identical resistors connected to a 10 V battery in series, what is the voltage drop…

Question

I have ten-ohms resistors available to connect and arrange in a series or parallel or in a combo of series and parallel.

If I need the resistance to be 35 ohms, how many of the ten resistors do I need to use? What does the configuration look like?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

When resistors with different resistances are connected in parallel, which of the following must be the same for each resistor? Choose all correct answers, (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given time interval (e) none of those answers
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
When resistors with different resistances are connected in series, which of the following must be the same for each resistor? Choose all correct answers. (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given time interval (e) none of those answers
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19
For the network in Figure P18.60, show that the resistance between points a and b is Rab=2717. (Hint: Connect a battery with emf across points a and b and determine /I, where I is the current in the battery.) Figure P18.60
Three 60.0-W, 120-V lightbulbs are connected across a 120-V power source, as shown in Figure P18.50. Find (a) the total power delivered to the three bulbs and (b) the potential difference across each. Assume the resistance of each bulb is constant (even though, in reality, the resistance increases markedly with current). Figure P18.50
In Figure P21.47, show how to add just enough ammeters to measure every different current. Show how to add just enough voltmeters to measure the potential difference across each resistor and across each battery.
For the two resistors shown in Figure 17.12, rank the currents at points a through f from largest to smallest. (a) Ia = Ib Ie = If Ic = Id (b) Ia= Ib Ic = Id Ie = If (c) Ie = If Ic = Id Ia = Ib Figure 17.12 (Quick Quiz 17.8)
Three 60.0-W, 120-V lightbulbs are connected across a 120-V power source, as shown in Figure P18.50. Find (a) the total power delivered to the three bulbs and (b) the potential difference across each. Assume the resistance of each bulb is constant (even though, in reality, the resistance increases markedly with current). Figure P18.50
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26