I need an answer with details as soon as possible please 1- Using resistors and capacitors, if you know that the capacitance of the capacitor is 100nf, design a Low Pass Filter with a frequency of 115HZ. 2- Using resistors and capacitors, if you know that the capacitance of the capacitor is 100nf, design High pass filters with a cut-off frequency of 215HZ .

I need an answer with details as soon as possible please 1- Using resistors and capacitors, if you know that the capacitance of the capacitor is 100nf, design a Low Pass Filter with a frequency of 115HZ. 2- Using resistors and capacitors, if you know that the capacitance of the capacitor is 100nf, design High pass filters with a cut-off frequency of 215HZ .

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

DESIGNPROBLEM_PSPICEMULTISIMUsing a 5 mH inductor, design a high-pass, RL, passive filter with a cutoff frequency of 25 krad/s . 1. a) Specify the value of the resistance. 2. b) Assume the filter is connected to a pure resistive load. The cutoff frequency is not to drop below 24 krad/s. What is the smallest load resistor that can be connected across the output terminals of the filter?
H.W2: a) Using 0.1 µF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jw,)where w, is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at wo?
DESIGNPROBLEM_Using a 100 nF capacitor, design a highpass passive filter with a cutoff frequency of 300 Hz. 1. a) Specify the value of R in kilohms. 2. b) A 47 kΩ resistor is connected across the output terminals of the filter. What is the cutoff frequency, in hertz, of the loaded filter?
RLC bandpass design： The target is to filter out the square-wave noise from the 120kHz sinsousidal signal using the RLC banpass filter (series LCR configuration). 1- Derive the transfer function for the following second order LCR filter. 2- Derive an expression for the resonant frequency and the quality factor of the filter. 3- The objective is to filter out the square-wave noise from the sinousidal 120kHz signal. The two closest frequency components of the square wave must be attenuated at least by a factor of √2. We suggest you to use either a 10 mH inductor. Calculate the required Q and the repsective R and C to achieve the filter requirement.
For the following bandpass filter circuit, select the circuit elements in order to satisfy the following specifications: fl= 100Hz fu= 200Hz First, consider the lowpass filter on the left, which has a transfer function Hw= Rf1/R11 1/Rf1C1jw+1 The desired lowpass transfer function, written in hertz frequency, is H(w)= -1/(jf/fu+1) If R1 is selected to be 1000Ω then determine R11 in ohms. Enter R11. Omit the units. (hint: remember to convert between fand w when needed) Referring to question 1, what is C1 in μf Consider the highpass filtter on the night, which has a transfer function H(w)= - Rf2/R12 R12/C2jw/R12C2jw+1.The desired highpass transfer function is -if/ft/if/ft+1. If R12 is selected to be 1000Ω then determine Rf2 in ohms and C2 in μf.Enter Rf2 (hint: remember to convert between fand w when needed) Referring to problem 3, what is C2 in μf
bandreject filter with a lower cutoff frequency of 400 Hz, an uppercutoff frequency of 4000 Hz, and a passband gain of 0 dB. Use theprototype filter circuits introduced in the design process.2. Draw the circuit diagram of the filter and label all of thecomponents.3. What is the transfer function of the scaled filter?4. Evaluate the transfer function derived in (c) at the center frequencyof the filter. 5. What is the gain (in decibels) at the center frequency?6. Using a computer program of your choice, make a Bode magnitudeplot of the filter transfer function.
Q2 ) a ) Design a broadband parallel bandreject filter with a lower cutoff frequency of 1000 rad / s , a bandwidth of 3000 rad / s , and a passband gain of 10. Use 0.5 uF capacitors b ) Draw the circuit of the filter in ( a ) , c ) Calculate the gain at the center frequency Q3 ) a ) Determine the order of a lowpass Butterworth filter that has a cutoff frequency of 1000 rad / sec and again of no more than -36 dB at 10000 rad / sec . b ) Using 1 kq resistors and ideal op amps , design a circuit that will implement the lowpass Butterworth filter specified in ( a ) The gain in the passband is one c ) Construct the circuit diagram and label all component values
DESIGNPROBLEM_PSPICEMULTISIM Use a 500 nF capacitor to design a bandreject filter, as shown . The filter has a center frequency of 4 kHz and a quality factor of 5. 1. a) Specify the numerical values of R and L. 2. b) Calculate the upper and lower corner, or cutoff, frequencies in kilohertz. 3. c) Calculate the filter bandwidth in kilohertz.
The voltage transfer function for either high-pass prototype filtershown isH(s)=ss+1. Show that if either circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=(s/kf)(s/kf)+1.
Examine the effect of placing a load resistor in parallel with the inductor in the RL high-pass filter shown : 1. Determine the transfer function for the circuit. 2. Sketch the magnitude plot for the loaded RL high-pass filter, using the values for R and L from the circuit and letting RL=R. On the same graph, sketch the magnitude plot for the unloaded RL high-pass filter.
DESIGNPROBLEM_1. The circuit is used in a third-order high-passunity-gain Butterworth filter that has a cutoff frequency of 5 kHz.Specify the values of R1 and R2 if 5 μF capacitors are available toconstruct the filter.2. Specify the values of resistance and capacitance in the first-ordersection of the filter.3. Draw the circuit diagram and label all the components.4. Give the numerical expression for the scaled transfer function ofthe filter.5. Use the scaled transfer function derived in (d) to find the gain in dBat the cutoff frequency.
Design a unity-gain parallel bandreject filter with a centerfrequency of 250 rad/s and a bandwidth of 2000 rad/s. Use 1 μFcapacitors, and specify all resistor values.