. A coil of 1 k Q resistance and 0.1 H inductance is connected in parallel with a variable capacitor across a 2.0 V,10kHz AC supplly as shown in figure 2.3. Analyse the operation of the circuit and determine the following: I. the capacitance of the capacitor when the supply current is a minimum 11. The effective impedance ZT of the circuit at resonance. lii. The Q-factor iv. The bandwidth v. the current in each branch vi. The supply current

. A coil of 1 k Q resistance and 0.1 H inductance is connected in parallel with a variable capacitor across a 2.0 V,10kHz AC supplly as shown in figure 2.3. Analyse the operation of the circuit and determine the following: I. the capacitance of the capacitor when the supply current is a minimum 11. The effective impedance ZT of the circuit at resonance. lii. The Q-factor iv. The bandwidth v. the current in each branch vi. The supply current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Show the capacitors, whether it is effective at low or high frequencsies Draw low frequency small-signal-equivalent circuit. AND LOWER corner is 82Hz frequency. Design the circuit. Draw the high frequency small-signal-equivalent circuit. AND UP-CORNER İS 172Hz frequency. DESİGN THE CIRCUIT.
A cable test unit is required to test cables of 5000 pf at 200 kV. The testing transformer available is 230 V/50 kV, 15 kVA with 2.5% resistance and 6% reactances. Determine the inductance required for resonant testing and input voltage to the testing transformer. Assume the resistance of inductor and leads to be 2.5%.
An inductor is attached to an AC voltage source. Which change will result in a halving of the current?A. Halving the voltage and doubling the frequencyB. Doubling the frequencyC. Halving the frequencyD. Doubling the voltage and halving the frequency
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
H.W For general pulse train shown below: A sin (nw,t) 2 A 1, show that ; Dn = 2. for a duty cyele %3D shou that : AT %3D Sinc (nT) To To 3. for a duty syele : To & A= 1 %3D Find Dn .
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
1. For the circuit in Figure 1: a) Calculate the total impedance Ztot of the below circuit b) Calculate the total current Itot and branch currents IR, Ic and IL. Calculate voltage Uc over the capacitance C. c) Is the circuit in resonance? How the parallel resonance affect inductance and ca- pacitance currents IL and Ic? E=230V 20°, R₁ = 10 Q, R₂= 2009, C= 100µF, L = 280mH, ƒ= 30Hz (Answers Ztot = 210 + 3.9j №, I =4.13A Z 90.1°) Present all values in polar form (x 2 yº) E I tot R₁ R2 IR Ic CU Į₁ L
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
Make an AC analysis with the circuit below. Full Solution.
In the non-sinusoidal wave circuits the peak value of infinite harmonic number is . . peak value of fundamental .... ...... wave. non-of-them
Impedance...