I need answer in 1hr do it fast. A shell-and-tube heat exchanger is set at the one shell pass and two tube passes. Hot air enters the shell at 90°C, and leaves at 50°C, whose mass flow rate is 5 kg/s. Cold water enters the tube at 23°C, whose flow rate is 3 kg/s. What is the water outlet temperature? What is the overall UA of the heat exchanger? a) Draw the problem diagram. b) List all required properties and equations to solve this problem. c) Solve the problem

I need answer in 1hr do it fast. A shell-and-tube heat exchanger is set at the one shell pass and two tube passes. Hot air enters the shell at 90°C, and leaves at 50°C, whose mass flow rate is 5 kg/s. Cold water enters the tube at 23°C, whose flow rate is 3 kg/s. What is the water outlet temperature? What is the overall UA of the heat exchanger? a) Draw the problem diagram. b) List all required properties and equations to solve this problem. c) Solve the problem

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.13P

See similar textbooks

Similar questions

A heat exchanger is heating water from 50 0 F to 160 0 F using steam on the shell at atmospheric pressure condensing at 212 0 F. If the overall U is 710 BTU/(hr 0 F ft2) and the exchange rate is 9,000,000 BTU/hr, what tube area is needed?
A one-shell, two-tube pass shell and tube heat exchanger has 1580 tubes with di = 13 mm and do = 16 mm. Tubes have an average length of 6 m per pass. Cold water enters the tubes at 30 C and a rate of 110 kg/s and hot water enters shell at 90 C and a rate of 125 kg/s. Find the rate of heat transfer, ∆TLMTD, and the overall heat transfer coefficient. Use stainless steel tubes and fi = 0.001 m2·K/W. [Ans.: 13 MW, 10.7 C, and 493 W/m2·K].
A still mill desires to cool 3000 gal/hr of an inorganic liquid from 250oF to 180oF by Lehigh River water flowing through a shell-and-tube exchanger at a rate of 5000 gal/hr. The liquid is somewhat acidic in nature and so an alloy exchanger is probably required.Within the plant is an unused S-and-T, floating-head exchanger have one shell pass and two tube passes. The shell is mild steel, and the tubes are type 304 stainless. Specifications of the surplus exchanger revel a 20-in I.D. shell with 158 1-in 14 BWG tubes 16 ft long laid out on a 1.25 in square pitch. Baffles are placed 6-in apart.Will the surplus exchanger be suitable for the cooling requirements? Assume the inorganicliquid has the physical properties of water.
A parallel Flow heat exchanger designed to heat fuel oil from 90℃ to 130℃, while the heating fluid enters at 160℃ and leaves 140℃. Calculate AMTD. ANSWER: 20℃
In a single pass, cross flow heat exchanger where two fluids are not mixed, water with a temperature of 35oC, a mass flow of 1 kg / s, a specific heat capacity of 4197 J / kgK, 250oC, a mass flow of 1.5 kg / s, a specific heat capacity of 1000J / kgK. heated by hot gas. If the heat transfer area of the heat exchanger is 40 m2 and the total heat transfer coefficient is 100 W / m2K, calculate the exit temperatures of the water and hot gas from the heat exchanger using the NTU method.
Incropera Heat Transfer 11.16 The hot and cold inlet temperatures to a concentric tube heat exchanger are Tim = 200°C, Tc; = 100°C, respectively. The outlet temperatures are Th„, = 110°C and 71.0 = 125°C. Is the heat exchanger operating in a parallel flow or in a counter flow configuration? What is the heat exchanger effectiveness? What is the NTU? Phase change does not occur in either fluid.
A heat exchanger is heating water on the tube side with steam condensing on the shell side. The water is entering at 45 0 F and exiting at 175 0 F. No instruments are available for measuring the tube side water flow but condensed steam from the shell side is being collected at a rate of 43 GPM. If the tube area of the exchanger is 350 Ft2 , and the overall heat transfer coefficient clean was 900 BTU/Hr.Ft2 F0, how much has the overall heat transfer coefficient changed, if at all? Note: Latent heat for water/steam at 212 0 F is 970 BTU per pound of water. A gallon of water weighs 8.34 lbs.