A fluid is flowing through a heat exchanger (HEX) at a rate of 2500 kg/h. The heat exchanger supplies 115,600 kJ/h. The inlet temperature of the fluid is 80C. Determine the outlet temperature of the product. The product specific heat 3.9 kJ/kg C

A fluid is flowing through a heat exchanger (HEX) at a rate of 2500 kg/h. The heat exchanger supplies 115,600 kJ/h. The inlet temperature of the fluid is 80C. Determine the outlet temperature of the product. The product specific heat 3.9 kJ/kg C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.14P

See similar textbooks

Related questions

Q: Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600…

A: Given Data m= 2000 kg/h Q= 111,600 kJ/h. To=95°C C=3.9 kJ/kgK

Q: In an heat exchanger of parallel flow type, water enters at 60°C and leaves at 80°C while oil of…

A: Given Data Tw1=60°C Tw2=80°C Sg=0.8 To1=250°C T02=100°C CpO=2.5 Kj/KgK T∞=300K mO=1Kg

Q: a power plant steam, steam is continuously extractedfromthe turbine and in a heat exchanger there is…

A: Data given- Q1 = 1200 kJ/hr Q2 =800 kJ/hr T1 = 20°C = 293 K

Q: Saturated propane vapor at 2:00 x 102 psia is fed to a well-insulated heat exchanger at a rate of…

A: From the table of propane,At 200psia, saturated vapour…

Q: The specific heat value in phase change heat exchangers is approximately a) 0 kJ/(kgC)…

Q: The radiator in an automobile is a cross-flow heat exchanger (UAs = 10 kW/K) that uses air (cp =…

A: Given data To determine exit temperature of cold fluid..??

Q: 30312 kj / h heat is given to the milk flowing with a mass flow rate of 40 kg / min in the plate…

Q: Liquid benzene at 38 C with a vapor pressure of 26.4 kN/m2 and a density of 860 kg/m3 is to be…

A: Given data as per question Pv=26.4 KNm2Q=0.0025 m3sη=0.6ρ=860 kgm3D=0.0409 mΔpf=3.45…

Q: To cool the lubricating oil, a concentric counter-flow heat exchanger (see Figure Q1) is utilized,…

A: Solution: Assumptions: There is no Fouling Resistance must be low in heat exchanger Tube wall is…

Q: . A double-pipe counter-flow heat exchanger is to cool ethylene glycol (Cp 2560 J/kg - 'C) flowing…

Q: Liquid water is heated inside the tubes of a shell and tube heat exchanger as shown in the figure…

A: Given data The mass flow rate in each tube is m˙=0.25 kgs. The diameter of the inside tube is di=16…

Q: Cold water (cp = 4.18 kJ/kg·K) enters a crossflow heat exchanger at 14°C at a rate of 0.35 kg/s…

A: It is required to determine the heat capacity rate of the hot fluid. It is required to determine…

Q: Water (cp = 1.0 Btu/lbm ℉) is to be heated by solar heated hot air (cp = 0.24 Btu/lbm ℉) in a…

Q: A natural gas-fired steam power plant consumes 360 kg/min of natural gas. If the heat losses to the…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 23–74C Consider a heat exchanger in which both fluids have the same specific heats but different…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Saturated steam at 126°C with a latent heat value of 2185 kJ/kg is condensing on the outer tube…

Q: Cold water (cp 5 4180 J/kg?K) enters the tubes of a heat exchanger with 2-shell passes and 20-tube…

Q: For a 1 shell, 30 tube heat exchanger, the inlet temperature of the shell is 8 C and the outlet…

A: The overall heat transferred by the heat exchanger can be calculated using the formula given below…

Q: Determine the Area of evaporator in m2 for 59 - Ton water cooled air-conditioning system that uses…

Q: A heat exchanger is heating water on the tube side with steam condensing on the shell side. The…

Q: Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid…

A: Heat is a form of energy that gets transferred from the high temperature region to the low…

Q: In a once-through boiler, feed water enters through the bottom of tubes, receives heat from…

A: Given data-pressure of feed water at turbine=22.0 MpaTf=523KSuper heated steem pressure…

Q: 5) During an experiment, a plate heat exchanger that is used to transfer heat from a hot-water…

Q: Problem #3: A double-pipe counter-flow heat exchanger is to cool ethylene glycol (Cp = 2560 J/kg-…

Q: Water flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is…

A: INTRODUCTION : Turbine is a work producing device, by taking energy from the inlet either compressor…

Q: The mass flow rate, specific heat, and inlet temperature of the tube-side stream in a double-pipe,…

A: Given data Below figure dipicts the given data

Q: Hot exhaust gases of a stationary diesel engine are to be used to generate steam in an evaporator.…

A: Given data as per question Entrance temperature of exhaust gasses = 5500 c Mass flow rate of gasses…

Q: The condenser of a room air conditioner is designed to reject heat at a rate of 15,000 kJ/h from…

A: The heat rejection is given as, The related diagram is given as, From the above diagram, the…

Q: 10. In a double-pipe counterflow heat exchanger, water at the rate of 60 kg/min is heated from 65 oC…

A: Given: The mass flow rate of water, mw = 60 kg/min The water inlet temperatures, Tw1 = 65 C The…

Q: Consider two heat exchanger configurations: parallel-flow and counter-flow. For both configurations…

Q: Steam 90°C 10. A shell-and-tube process heater is to be selected to heat water (Cp 4190 J/kg-°C)…

Q: Automobile air-conditioner gives up 18 kW at 65 km/h if the outside temperature is 35°C. The…

A: let C1 and C2 are constant V= velocity of air m˙a=C1VU=C2V-0.7U=200=C2650.7C2=10.76

Q: Write about of the following related to shell and tube heat exchanger: (i) Tube sheet and tube pitch…

A: Given Shell and tube exchanger To find Relation Tube sheet and tube pitch Baffle and baffle spacing…

Q: Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600…

A: Given Data Mass flow rate= 2000 kg/h Q=111600 kJ/h To=95°C C=3.9 kJ/kg.K

Q: in a 10-m long center-current flow tubular heat exchanger, a liquid food, flowing in the inner pipe…

Q: Oil at a rate of 0.8 kg/sec enter a shell and tube counter flow heat exchanger at 150°C and leaves…

Q: In a double-pipe, counter-flow heat exchanger, water entering at 1.5 kg/s is heated from 25°C to…

Q: In a double-pipe, counter-flow heat exchanger, water entering at 1 kg/s is heated from 23°C to 69°C…

Q: A 10-m-long countercurrent-flow heat exchanger is being used to heat a liquid food from 20 to 80 C.…

Q: In a single-body, four-pipe transition heat exchanger, the hot combustion product gases are cooled…

A: Given data: The mass flow rate of gas is mh=3 kgs The specific heat of the gas is Ch=0.95 kJkg°C The…

Q: 13–122 Consider a water-to-water counter-flow heat ex- changer with these specifications. Hot water…

Q: QUESTION 5 The mass flowrate, specific heat, and inlet temperature of the tube-side stream in a…

Q: It is proposed to build a 1000 MWelectric power plant with steam as the working fluid. The…

Q: Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid…

Q: Crude oil at 198°C is to be cooled to 39°C. The oil flow-rate is 6.032 kg/s. Cooling water is…

Q: In a shell and tube heat exchanger _________________________ a.The relationship between temperature…

A: In a shell and tube heat exchanger ,it is feasible to turn off the ports and instead assume a…

Concept explainers

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop systems.
Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600 kJ/h. The outlet temperature of the product is 95C. Determine the inlet temperature of the milk. The product specific heat 3.9 kJ/kg degrees C
Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600 kJ/h. The outlet temperature of the product is 95°C. Determine the inlet temperature of the milk. The product specific heat 3.9 kJ/kg°C. Answer must be 80.69°C
In a power plant steam, steam is continuously extracted from the turbine and in a heat exchanger there is a condensation of the extracted steam. The energy released during condensation of steam is used to operate a heat engine. A heat engine receives thermal energy at a rate of 1200 kJ/min from condensing steam and rejects waste heat to a lake at 25°C at a rate of 850 kJ/min. Determine the lowest possible condensing steam temperature.
In an heat exchanger of parallel flow type, water enters at 60°C and leaves at 80°C while oil of specific gravity 0.8 enters at 250°C and leaves at 100°C. The specific heat of oil is 2.5 kJ/kg K and surrounding temperature is 300 K. Determine the loss in availability on the basis of one kg of oil flow per second.
The condenser of a room air conditioner is designed to reject heat at a rate of 15,000 kJ/h from refrigerant-134a as the refrigerant is condensed at a temperature of 40°C. Air (cp = 1005 J/kg·K) flows across the finned condenser coils, entering at 25°C and leaving at 35°C. If the overall heat transfer coefficient based on the refrigerant side is 150 W/ m2·K, determine the heat transfer area on the refrigerant side.
In a countercurrent double-pipe heat exchanger, the hot oil entering the inner tube at 420 K with a flow rate of 60 g/s is required to be cooled to 320 K. In the space between the outer tube and the inner tube of the heat exchanger, cooling water flows at the same linear speed as the oil. Cooling water enters the heat exchanger at 290 K. The inner tube inner diameter of the heat exchanger is 25 mm and the outer tube inner diameter is 40 mm. Calculate the length of the heat exchanger. The oil side heat transfer coefficient is 1.6 kW/m2 K, and the water side heat transfer coefficient is 3.6 kW/m2 K. The densities of oil and water can be taken as 0.8 and 1.0 g/cm3, respectively, and the specific heats of oil and water can be taken as 2.0 and 4.2 kJ/kg K, respectively. Wall effects can be neglected. Flow cross-sectional area = (PI)*D2 /4 F2
Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid enters 5 kg/sec and with an inlet temperature of 60 C. Determine the maximum heat transfer that can happen during the heat exchange process? Take specific heat value of the fluid as 2000 J/(kgC)
The enthalpy of steam entering the turbine inlet is 2750 kJ/kg and leaving turbine at 1750 kJ/kg. The enthalpy of saturated liquid is 190 kJ/ kg and enthalpy of dry saturated steam 2600 kJ/kg corresponding to the condenser pressure. The quality of steam at the exit of turbine is
Hot fluid enters at a flow rate of 3 kg/sec with an inlet temperature of 150 C while cold fluid enters 5 kg/sec and with an inlet temperature of 60 C. Determine the maximum heat transfer that can happen during the heat exchange process? Take specific heat value of the fluid as 2000 J/(kgC) not sufficient information 150 kW 1 MW 540 kW none of the given 900 kW
Water flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is used to provide additional energy to the water between the two turbines. The first turbine has a power output of 8,000 kW. Determine the power output of the second turbine in kW and the process efficiency of each turbine. Determine the state of steam in turbine 1, Formulate the 1st Law for turbine 1, and solve for the flow rate of steam. Formulate the 1st Law for the heat exchanger, and solve for the temperature at exit
730312 kj / h heat is given to the milk flowing with a mass flow rate of 40 kg / min in the plate heat exchanger and the milk leaves the heat exchanger at 96. The specific heat of milk is 3.86 kj / kg. Accordingly, calculate the milk inlet temperature to the heat exchanger. A.) 25 ℃ B.) 100.73 ℃ C.) 15 ° C D.) 17.17 ℃ E.) 91.27 ℃