A soft surface cone clutch must handle 1865 In-1b of torque at 1250 rpm. The large diameter of the clu is 13.75 in. and the included angle in 12.5°. The face width of the bearing surfaces is 2.5 in. Using efficient of friction 0.20. determine (a) the force (F) to engage the clutch, (b) the required normal unit pa sure on the contact surfaces when operation is at capacity Ans. 428 lb. 13.15 psi

A soft surface cone clutch must handle 1865 In-1b of torque at 1250 rpm. The large diameter of the clu is 13.75 in. and the included angle in 12.5°. The face width of the bearing surfaces is 2.5 in. Using efficient of friction 0.20. determine (a) the force (F) to engage the clutch, (b) the required normal unit pa sure on the contact surfaces when operation is at capacity Ans. 428 lb. 13.15 psi

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.77P: The cone clutch transmits the torque C through a conical friction surface with cone angle . The...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
A multiple-disk clutch with 17 disks, 8 disks turning with one shaft and 9 with the other shaft, is rated at 25 hp at 500 rpm. The outside and inside diameters of the disks are 5½ and 2½ in., respectively. The coefficient of friction is 0.2. (a) Determine the axial force required to transmit the rated torque and determine the pressure between the disks.
A centrifugal clutch is to be designed to transmit 15 kW at 900 r.p.m. The shoes are four in number. The speed at which the engagement begins is 3/4th of the running speed. The inside radius of the pulley rim is 150 mm. The coefficient of friction may be taken as 0.25. Determine: 1. mass of the shoes, and 2. size of the shoes.
A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20 hy turning at 800 rpm. For a cone angle of 20 degrees and a coefficient of friction 0.30, determine the force required to keep the surface in contact. Ans. 121.5 lb.
A multi-disk clutch consists of two steel disks with one bronze disk. Theinner and outer diameters of the contacting surfaces are 200 and 250 mmrespectively. The coefficient of friction is 0.1 and the maximum pressurebetween the contacting surfaces is limited to 0.4 N/mm2. Assuming uniformwear theory, calculate the required force to engage the clutch and the powertransmitting capacity at 720 rpm
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.
The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an inner diameter of 250 mm. The average value of the coefficient of friction is 0.25, and the operating force is 5 kN. Find the torque capacity when the clutch is new, the maximum pressure and the torque capacity after a sufficiently long operating period.
A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial forcerequired if the capacity of the clutch is 8 KW at 500 rpm. The mean diameter of the active conicalsections is 300 mm. Use uniform wear method.
A multiple disc clutch is used to operate the speed regulating gears of lathe. If the torque delivered by the clutch is 400 lbs.in , evaluate the number of discs are necessary and the max. force acting on them while the clutch is in operation. Limit the disc friction surface sizes between 5 in. and 3 in. Take the factor of safety as 2 , coefficient of friction varies from 0.150 to 0.200 , and the pressure as 99.76 psi.