Determine the snear sStress Try tnat acts at point BExpress your answer to three significant figures and include appropriate units.The rod has a diameter of 40 mm. (Figure 1) It is subjectedto the force system F, = 1630 N, F, = 640 N,F, = 800 N.μΑ(tB)zyValueUnitsSubmitRequest AnswerPart CFigure1 of 1Determine the shear stress Trz that acts at point BExpress your answer to three significant figures and include appropriate units.100 mmHA(tB)=z =ValueUnits300 mmSubmitRequest Answer100 N-mF,F( Return to AssignmentProvide Feedback I ReviewExpress your answer to three significant figures and include appropriate units.The rod has a diameter of 40 mm. (Figure 1) It is subjectedto the force system F, = 1630 N, F, = 640 N,F = 800 N.μΑ?31.87MPаOB =SubmitPrevious Answers Request AnswerFigure1 of 1Part BDetermine the shear stress Try that acts at point B.Express your answer to three significant figures and include appropriate units.100 mm300 mm?(тв)уValueUnits100 N-mF,F-SubmitRequest AnswerF,

find the shear stress at point B

I Review Express your answer to three significant figures and include appropriate units. The rod has a diameter of 40 mm (Figure 1) It is subjected to the force system F, = 1630 N, F, = 640 N, F. = 800 N. HA ? OB = 31.87 MPа Submit Previous Answers Request Answer Figure 1 of 1 Part B Determine the shear stress Tzy that acts at point B. Express your answer to three significant figures and include appropriate units. 100 mm THHẢ 300 mm ? (TB)zy = Value Units 100 N-m F, Submit Request Answer

I Review Express your answer to three significant figures and include appropriate units. The rod has a diameter of 40 mm (Figure 1) It is subjected to the force system F, = 1630 N, F, = 640 N, F. = 800 N. HA ? OB = 31.87 MPа Submit Previous Answers Request Answer Figure 1 of 1 Part B Determine the shear stress Tzy that acts at point B. Express your answer to three significant figures and include appropriate units. 100 mm THHẢ 300 mm ? (TB)zy = Value Units 100 N-m F, Submit Request Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
Explain the method of representing the combination of normal and shear stresses acting on any plane through an incremental element on shear stress–normal stress coordinates.
A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.
A cylinder which can be considered as a thin-walled shell, is made of steel plate 16 mm thick and is 2.14 m internal diameter. The cylinder is subjected to an internal fluid pressure of 0.55 MN/m2 gauge and, at the same time rotated about its longitudinal axis at 3000 rev/min. Determine:(a) the hoop stress induced in the wall of the cylinder due to rotation:(b) the hoop stress induced in the wall of the cylinder due to the internal pressure:(c) the factor of safety based on an ultimate stress of the material in simple tension of 456 MN/m2. Steel has a density of 7.8 Mg/m3.
Before loading the plate, mark a line with the inclination shown. After the load is applied, the slope of the line decreases by 5x10^-3 rad. Determine the normal stress ?. Consider E = 2.1x106 kgf/cm^2 and v = 0.30. Express your answer in units of kgf/cm^2.
PLSS ANSWER ASAPPP Which is correct about spherical shell? a It has the same formula as hoop stress b The wall of the pressurized spherical vessel is subjected to uniform comporessive stress in all directions c It has the same formula as the tangential stress d The wall of the pressurized spherical vessel is subjected to uniform tensile stress in all directions
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
The block is subjected to a centrally-applied force of P=4.3 kipP=4.3 kip. Part A Determine the average normal stress on the material. Express your answer to three significant figures and include appropriate units.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar. Express your answer in MPa.
For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to define the diameter of the Mohr's Circle? (50 MPa, 25 MPa) (- 80 MPa, - 25 MPa) (- 80 MPa, 25 MPa) (50 MPa, - 25 MPa)