I Review | Constants A thin, uniform rod is bent into a square of side length a. Part A If the total mass is M, find the moment of inertia about an axis through the center and perpendicular to the plane of the square. Use the parallel-axis theorem. Express your answer in terms of the variables M and a. ΑΣφ Submit Request Answer II

I Review | Constants A thin, uniform rod is bent into a square of side length a. Part A If the total mass is M, find the moment of inertia about an axis through the center and perpendicular to the plane of the square. Use the parallel-axis theorem. Express your answer in terms of the variables M and a. ΑΣφ Submit Request Answer II

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 10.5CYU: Check Your Understanding What is the moment of inertia of a cylinder of radius R and mass m about an...

See similar textbooks

Similar questions

A system of point particles is rotating about a fixed axis at 4 rev/s. The particles are fixed with respect to each other. The masses and distances to the axis of the point particles are m1=0.1kg , r1=0.2m , m2=0.05kg , r2=0.4m , m3=0.5kg , r3=0.01m . (a) What is the moment of inertia of the system? (b) What is the rotational kinetic energy of the system?
The angular acceleration of a rotating rigid body is given by =(2.0-3.0t)rad/s2 . If the body starts rotating from rest at t=0 , (a) what is the angular velocity? (b) Angular position? (c) What angle does it rotate through in 10 s? (d) Where does the vector perpendicular to the axis of rotation indicating 0 at t=0 lie at t=10s ?
A uniform rod of mass and length is held vertically by two strings of negligible mass, as shown below. (a) Immediately after the string is cut, what is the linear acceleration of the free end of the stick? (b) Of the middle of the stick?
The centrifuge at NASA Ames Research Center has a radius of 8.8 m and can produce farces on its payload of 20 gs or 20 times the force of gravity on Earth. (a) What is the angular momentum of a 20-kg payload that experiences 10 gs in the centrifuge? (b) If the driver motor was turned off in (a) and the payload lost 10 kg, what would be its new spin rate, taking into account there are no frictional forces present?
A diver off the high board imparts an initial rotation with his body fully extended before going into a tuck and executing three back somersaults before hitting the water. If his moment of inertia before the tuck is 16.9kgm2 and after the tuck during the somersaults is 4.2kgm2 , what rotation rate must he impart to his body directly off the board and before the tuck if he takes 1.4 s to execute the somersaults before hitting the water?
A massless tether with a masses tied to both ends rotates about a fixed axis through the center. Can the total acceleration of the tether mass combination be zero If the angular velocity Is constant?
Explain how you might use the apparatus described in Figure OQ10.7 to determine the moment of inertia of the wheel. Note: If the wheel does not have a uniform mass density, the moment of inertia is not necessarily equal to 12 MR2.
A top has moment of inertia 3.2104kgm2 and radius 4.0 cm from the center of mass to the pivot point. If it spins at 20.0 rev/s and is precessing, how many revolutions does it precess in 10.0 s?
On takeoff, the propellers on a UAV (unmanned aerial vehicle) increase their angular velocity form rest at a rate of =(25.0t)rad/s for 3.0 s. (a) What is the instantaneous angular velocity of the propellers at t=2.0s ? (b) What is the angular acceleration?
Check Your Understanding What is the moment of inertia of a cylinder of radius R and mass m about an axis through a point on the surface, as shown below? A uniform thin disk about an axis through the center Integrating to find the moment of inertia of a two-dimensional object is a little bit trickier, but one shape is commonly done at this level of study—a uniform thin disk about an axis through its center (Figure 10.27). Figure 10.27 Calculating the moment of inertia for a thin disk about an axis through its center.
The axis of Earth makes a 23.5 angle with a direction perpendicular to the plane of Earth’s orbit. As shown below, this axis precesses, making one complete rotation in 25,780 y. (a) Calculate the change in angular momentum in half this time. (b) What is the average torque producing this change in angular momentum? (c) If this torque were created by a pair of forces acting at the most effective point on the equator, what would the magnitude of each force be?
You have a grindstone (a disk) that is 90.0 kg, has a 0.340-m radius, and is turning at 90.0 rpm, and you press a steel axe against it with a radial force of 20.0 N. (a) Assuming the kinetic coefficient of friction between steel and stone is 0.20, calculate the angular acceleration of the grindstine. (b) How many turns will the stone make before coming to rest?