I Review Part A The beam in (Figure 1) is made from three boards nailed together as shown. If the moment acting on the cross section is M = 630 N - m, determine the resultant force the bending stress produces on the top board. Express your answer to three significant figures and include appropriate units. HẢ F = Value Units Submit Request Answer Figure < 1 of 1 > Provide Feedback Next > 25 mm 150 mm 20 mm 200 mm 20 mm

I Review Part A The beam in (Figure 1) is made from three boards nailed together as shown. If the moment acting on the cross section is M = 630 N - m, determine the resultant force the bending stress produces on the top board. Express your answer to three significant figures and include appropriate units. HẢ F = Value Units Submit Request Answer Figure < 1 of 1 > Provide Feedback Next > 25 mm 150 mm 20 mm 200 mm 20 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.10.9P

See similar textbooks

Similar questions

Determine the plastic modulus Z and shape factor/for a W 12 x 14 wide-flange beam. Obtain the cross-sectional dimensions and section modulus of the beam from Table F-l(a) in Appendix F.
The beam in (Figure 1) is made from three boards nailed together as shown. If the moment acting on the cross section is M=500N⋅m, determine the maximum bending stress in the beam. Express your answer to three significant figures and include appropriate units.
Determine the largest intensity of the distributed load ww and its length xx on the beam so that the beam remains in the horizontal position when it is loaded. Express your answers, separated by a comma, to three significant figures. Given: The rigid beam is supported at its ends by two A-36 steel tie rods. (Figure 1) The rods have diameters dAB=0.51 in.dAB=0.51 in. and dCD=0.29 in.dCD=0.29 in. The allowable stress for the steel is σallow=16.6 ksiσallow=16.6 ksi.
Consider that the section is transmitting a positive bending moment about the z axis,Mz, where Mz=10 kip*in if the dimensions of the section are given in ips units, or Mz=1.13kN*m if the dimensions are in SI units. Determine the resulting stresses at the top and bottom surfaces and at every abrupt change in the cross section. Find the second moment of area, the location of the neutral axis, and the distances from the neutral axis to the top and bottom surfaces.
For the simply supported beam carrying the concentrated load P = 276 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 2.16 m, E = 12.77 GPa , and I =1681393mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU!
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 40.4 ksi. Assume P = 51 kips, L1=6.6 ft, and L2=19.8 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm thickand the web is 20mm thick. Determine the maximum bending moment that should be imposed in the sectionif the tensile or the compressive stressis not to exceed 40MN/m^2 and what percentage of the moment is resisted by flange or web?
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m?
Wooden beams and steel plates are securely bolted together to form the composite member shown. Using the data given below, determine the largest permissible bending moment when the compos-ite member is bent about a horizontal axis.Modulus of elasticity 2 * 106 psi 29 * 106 psi Allowable stress 2000 psi 22 ksi
The composite beam in Fig. a is made of wood and reinforced with a steel strap located on its bottom side. If the beam is subjected to a bending moment of M = 2 kN # m, determine the normal stress at points B and C. Take Ew = 12 GPa and Est = 200 GPa.
Determine the ratios of the weights of four beams that have same length.are made of the same material,are subjected to the same lmaximum bending moment,and have the same maximum bending stress if their cross sections are (I) a rectangle with height equal to twice the width,(2) a square,(3) a circle , and (4) a pipe with outer diameter d and wall thickmess f = di% (see figures).