I want to know how this four pressures and enthalpies are selcected 8.6. A steam power plant employs two adiabatic turbines in series. Steam enters the firstturbine at 650°C and 7000 kPa and discharges from the second turbine at 20 kPa. Thesystem is designed for equal power outputs from the two turbines, based on a turbineefficiency of 78% for each turbine. Determine the temperature and pressure of thesteam in its intermediate state between the two turbines. What is the overall efficiencyof the two turbines together with respect to isentropic expansion of the steam from theinitial to the final state?A steam power plant employs two adiabatic turbines in series. Steam enters the first turbine at 650and 7,000 kPa and discharges from the second turbine at 20 kPa. The system is designed for equalpower outputs from the two turbines, based on a turbine efficiency of 78% for each turbine.Given the initial temperature and pressure to be T₁ = 923.15K, P₁ = 7000kPaH₁ = 3766.38kJ/kgHence from steam tables,S₁ = 7.22kJ/kgKAt 20 kPa, the values for saturated liquid and vapour are as follows:Hlig = 251.45kJ/kg, Hvap = 2609.9kJ/kgSliq=0.832kJ/kgK, Svap = 7.909kJ/kgKThe four values of pressure and the corresponding enthalpies are as follows:725750775800P₂kPa, H₂3023.93032.53040.93049.0Actual work is given by n(h₂' -h₁)H₂act=The actual enthalpy and entropy are hence-579.15 +3766.4-572.442 +3766.4-556.89 +3766.4559 579 3766 4.0.78(3023.93766.4)0.78(3032.5 3766.4)0.78 (3040.93766.4)0.78(30493766.4)3187.33194.03200.53206 8.why this 4 Pressuresare selected?kJ/kg=-579.15-572.442-565.89-559.512

Since in solution we have given Four pressure values: and

Answered: I want to know how this four pressures…

Engineering

Mechanical Engineering

I want to know how this four pressures and enthalpies are selcected

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a regenerative gas-turbine power plant with two stages of compression and two stages of expansion. The overall pressure ratio of the cycle is 9. The air enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. Accounting for the variation of specific heats with temperature, determine the minimum mass flow rate of air needed to develop a net power output of 110 MW.
Compare the thermal efficiency of a two-stage gas turbine with regeneration, reheating, and intercooling to that of a three-stage gas turbine with the same equipment when all components operate ideally.
Air enters the compressor of a regenerative gasturbine engine at 310 K and 100 kPa, where it is compressed to 900 kPa and 650 K. The regenerator has an effectiveness of 80 percent, and the air enters the turbine at 1400 K. For a turbine efficiency of 90 percent, determine the thermal efficiency. Assume variable specific heats for air.
Air enters the compressor of a regenerative gas-turbine engine at 310 K and 100 kPa, where it is compressed to 900 kPa and 650 K. The regenerator has an effectiveness of 80 percent, and the air enters the turbine at 1400 K. For a turbine efficiency of 90 percent, determine (a) the amount of heat transfer in the regenerator and (b) the thermal efficiency. Assume variable specific heats for air.
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of 1250 and 2 psia. The mass flow rate of steam through the cycle is 75 lbm/s. The moisture content of the steam at the turbine exit is not to exceed 10 percent. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the minimum turbine inlet temperature, (b) the rate of heat input in the boiler, and (c) the thermal efficiency of the Cycle. Answers:
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
A gas turbine cycle with a stage of reheat and regeneration operates under the conditions given below, as illustrated in the figure. The turbine efficiencies are 86%, and the compressor efficiency is 81%. Furthermore, the work output of the high-pressure turbine is just enough to drive the compressor. Determine the pressure at which the reheater operates. T1 = 1300 K, T6 = 3000 K, P1 = 450 kPa, P6 = 100 kPa
In an air standard gas turbine cycle, air at 14.5 psia and 70 F is first compressed to 80 psia in a compressor of 82 percent efficiency. The hot air leaving the combustion chamber at 1250 F is expanded back to 14.5 psia in a turbine of 85 percent efficiency. If a regenerator is inserted into the cycle to heat the air leaving the compressor to 650 F, determine the thermal efficiency of the cycle and the effectiveness of the regenerator.
A turboprop aircraft propulsion engine operates where the air is at 8 psia and −10°F, on an aircraft flying at a speed of 600 ft/s. The Brayton cycle pressure ratio is 10, and the air temperature at the turbine inlet is 940°F. The propeller diameter is 10 ft and the mass flow rate through the propeller is 20 times that through the compressor. Determine the thrust force generated by this propulsion system. Assume ideal operation for all components and constant specific heats at room temperature.
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of 1250 and 2 psia. The mass flow rate of steam through the cycle is 75 lbm/s. The moisture content of the steam at the turbine exit is not to exceed 10 percent. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the minimum turbine inlet temperature, (b) the rate of heat input in the boiler, and (c) the thermal efficiency of the cycle.
The turbine section of a Brayton cycle gas turbine receives the hot compressed air at 150 psia and 2100 °R, expand it to 15 psia and develops a gross output of 15,000 hp. Air enters the compressor at 500 R. Determine a) mass of air required, lb/s, b) compressor power required, c) net power output, and d) cycle efficiency. Show pV and Ts diagram. (THERMODYNAMICS 2)
Steam at 2000 psia and 1000°F enters the high-pressure turbine of a reheat cycle and is expanded adiabatically and reversibly to 200 psia. The steam is then passed through the superheater, from where it exits at the 950°F temperature. The low-pressure turbine expands the steam reversibly and adiabatically to 1 psia. If 7 lbm/s of steam is used and the circulating pump is assumed to operate ideally, the power produced, the added heat rate, and the cycle efficiency are: a) 7049,76 hp ; 12124,5 Btu/s ; 42,2% b) 7400,77 hp ; 11553,7 Btu/s ; 45,1% c) 8350,08 hp ; 13089,6 Btu/s ; 49,8% d) 7944,76 hp ; 11834,2 Btu/s ; 47,6%