Identical cylinders of weight and radiusare pushed by a series of moving arms. The coefficient of friction between all surfaces is . Denoting by the magnitude of the acceleration of the arms, derive an expression for (a) the maximum allowable value of if each cylinder is to roll without sliding, (b) the minimum allowable value of if each cylinder is to move to the right without rotating. Part (c) Let, and between all surfaces. Determine the horizontal component of the force exerted on each cylinder when the acceleration is (1) to the right and (2) 10 to the right. Benchmark solutions for part (c) are given as (1) 1.456 lb to the right, (2) 2.66 lb to the right. For part (c), your solution should be coded into MATLAB so it can easily be run for alternate cases. Part (d) Plot the horizontal component of the force exerted on each cylinder for different ranges of acceleration, which illustrate the various case of rolling and sliding obtained in parts (a) and (b).

Identical cylinders of weight and radiusare pushed by a series of moving arms. The coefficient of friction between all surfaces is . Denoting by the magnitude of the acceleration of the arms, derive an expression for (a) the maximum allowable value of if each cylinder is to roll without sliding, (b) the minimum allowable value of if each cylinder is to move to the right without rotating. Part (c) Let, and between all surfaces. Determine the horizontal component of the force exerted on each cylinder when the acceleration is (1) to the right and (2) 10 to the right. Benchmark solutions for part (c) are given as (1) 1.456 lb to the right, (2) 2.66 lb to the right. For part (c), your solution should be coded into MATLAB so it can easily be run for alternate cases. Part (d) Plot the horizontal component of the force exerted on each cylinder for different ranges of acceleration, which illustrate the various case of rolling and sliding obtained in parts (a) and (b).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The block and tackle shown are used to raise a 150-lb load. Each of the 3-in.-diameter pulleys rotates on a 0.5-in.-diameter axle. Knowing that the coefficient of static friction is 0.20, determine the tension in each portion of the rope as the load is slowly raised.
The 50-lb block A and the 25-lb block B are supported by an incline that is held in the position shown. Knowing that the coefficient of static friction is 0.15 between all surfaces of contact, determine the value of θ for which motion is impending.
A 15° wedge is forced under a 50-kg pipe as shown. Knowing that the coefficient of static friction at both surfaces of the wedge is 0.20, determine the largest coefficient of static friction between the pipe and the vertical wall for which slipping will occur at A.
The 50-lb block A and the 25-lb block B are supported by an incline that is held in the position shown. Knowing that the coefficient of static friction is 0.15 between the two blocks and zero between block B and the incline, determine the value of θ for which motion is impending.
In the pivoted motor mount shown, the weight W of the 175-lb motor is used to maintain tension in the drive belt. Knowing that the coefficient of static friction between the flat belt and drums A and B is 0.40 and neglecting the weight of platform CD , determine the largest couple that can be transmitted to drum B when the drive drum A is rotating clockwise.
The block and tackle shown are used to lower a 150-lb load. Each of the 3-in.-diameter pulleys rotates on a 0.5-in.-diameter axle. Knowing that the coefficient of static friction is 0.20, determine the tension in each portion of the rope as the load is slowly lowered.
The 12-lb uniform disk shown has a radius of r = 3.2 in. and rotates counterclockwise. Its center C is constrained to move in a slot cut in the vertical member AB, and an 11-lb horizontal force P is applied at B to maintain contact at D between the disk and the vertical wall. The disk moves downward under the influence of gravity and the friction at D. Knowing that the coefficient of kinetic friction between the disk and the wall is 0.12 and neglecting friction in the vertical slot, determine (a) the angular acceleration of the disk, (b) the acceleration of the center C of the disk.
A 10° wedge is used to split a section of a log. The coefficient of static friction between the wedge and the log is 0.35. Knowing that a force P with a magnitude of 600 lb was required to insert the wedge, determine the magnitude of the forces exerted on the wood by the wedge after insertion.
The cylinder shown has a weight W and radius r , and the coefficient of static friction μsis the same at A and B . Determine the magnitude of the largest couple M that can be applied to the cylinder if it is not to rotate.
The speed of the brake drum shown is controlled by a belt attached to the control bar AD . Knowing that a= 4 in., determine the maximum value of the coefficient of static friction for which the brake is not self-locking when the drum rotates counterclockwise.
A garage door is mountedon an overhead rail (Fig.).The wheels at A and B have rustedso that they do not roll, but ratherslide along the track. The coefficientof kinetic friction is 0.52. The distancebetween the wheels is 2.00 m,and each is 0.50 m from the verticalsides of the door. The door is uniformand weighs 950 N. It is pushedto the left at constant speed by a horizontalforce F S , that is applied as shown in the figure. (a) If the distanceh is 1.60 m, what is the vertical component of the force exerted on eachwheel by the track? (b) Find the maximum value h can have withoutcausing one wheel to leave the track.
End A of a slender, uniform rod of length L and weight W bears on a surface as shown, while end B is supported by a cord BC Knowing that the coefficients of friction are µs = 0.40 and µk = 0.30, determine (a) the largest value of 6 for which motion is impending, (b) the corresponding value of the tension in the cord.