If an offset is laid out 3° from its true direction on the field. Find the Limiting length of offset (m) so that the displacement of the point on the paper may not exceed 0,25mm. The scale of plotting is 1 5000

If an offset is laid out 3° from its true direction on the field. Find the Limiting length of offset (m) so that the displacement of the point on the paper may not exceed 0,25mm. The scale of plotting is 1 5000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Ex 20 The shear strength parameters of N.C.C. are; $=15$=30* a) In a Cutest on the same soil, the…

A: A direct shear test is a laboratory or field test used by geotechnical experts to measure the shear…

Q: When filled to capacity, the unpressurized storage tank shown contains water to a height of h= 20…

A: Given t = 0.625 inch H = 20 ft Diameter = 8 ft

Q: Compute the maximum velocity that car could pass through a sag parabolic curve having a sight…

Q: Find the equilibrium cant (in cm) on a 2 degree curve on a broad gauge if 15 trains, 10 trains, 5…

Q: Calculate the maximum shear stress and maximum bending stress in the section shown if the total…

A: Answer Calculation of Maximum bending stress We know that Maximum Bending stress is given by fb =…

Q: Draw I.L for bi, jk, de, ef, Im, bj, ke, jc and Rh.

A: Influence Line DiagramsThe influence line diagram is the graphical representation of any stress…

Q: In a plain strain condition in XY plane, normal strain in X and Y direction are equal to zero and…

A: Given: A plain strain condition in XY plane, Normal strain in X and Y direction are equal to zero…

Q: A column has a rectangular cross-section of 10 mm x 20 mm and effective length of 1 m. The ratio of…

A: Given: A column has a rectangular cross section = 10 mm×20 mm b=10 mmd=20 mm Effective length, L = 1…

Q: For the given failure surface of the soil, the unit weight for both the soil A and B is 19 kN/m³. O…

A: Given data- Failure surface of the soil is shown in figure- Unit weight of both soils = 19 kN/m3,…

Q: A wastewater is to be disinfected with 35mg/L of chlorine to obtain 99% kill of micro-organisms. The…

Q: For a U type manometer, a special manometer fluid with a density of 700 ∓ 1 kg/m3 is used. One end…

A: Given The manometer fluid has a density =700kg/m3 The local atmospheric pressure is pa = 744 mm…

Q: A steel rod, circular in cross-section, tapers from 30 mm diameter to 15 mm diameter over a length…

Q: 4 kN 8 kN 8 KN 4 kN 2m 2m 2 m 3 kN 6 kN 6 kN 3 kN 2 m 2m 2 m

Q: A hydraulic pipeline 3 km long and 50 cm in diameter is used to convey water with a velocity of 1.5…

Q: The beam has a Young's modulus of Eo =100 GPa, a length of 1 = 4 m and 2nd moment of area of I₂ = 4…

A: Given: E = 100 GPa = 100 x 109 N/m2 Iz = 4 m4 l = 4 m w = 100 N/m

Q: x 18 The effective shear strength equation (S = T₁ = 25+5 tam 30); expressed for a saturated clayey…

Q: 1. An equation has been calibrated for the amount of time (in seconds) required to clear N vehicles…

A: 1. Solution: T=2.06+2.35N The above equation represents the amount of Green time required to…

Q: A rotary is to be designed having average entry width of 5.5 m, width of weaving section is 11 m and…

Q: Problem Solving. 1. A 300 mm diameter circular beam carries a uniformly distributed load of w (kN/m)…

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

Q: An ascending gradient of 1 in 80 meets a descending gradient of 1 in 40. The length of summit curve…

A: Given- Ascending gradient = 1 in 80 , Descending gradient = 1 in 40, Overtaking sight distance OSD =…

Q: Practice Problem 1 Given the following girder properties: BY A = 11500 mm² d = 350 mm b = 250 mm t₁…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Which of the following statements about recrystallisation of metals are true? Select one or more: O…

A: Answer We know that Recrystallisation temperature is 0.3 - 0.4 times melting point for metals and…

Q: With the aid of relevant equations explain what is meant by "settling ratio" b) Explain the…

A: Solution: a) With the aid of relevant equations explain what is meant by "settling ratio" The…

Q: No.2 Determine the reactions and draw the shear and bending moment diagrams for the beam shown in…

A: As per guidelines, the question is solved by first method only .i.e. double integration method

Q: Draw I.L for members a, b, c & d.

A: ###Determination of ILD for member a , b , c , d #######

Q: 7. What causes tensile strength? 8. What are the three different ways tensile strength is measured?

A: This question is from Strength of materials.

Q: A car follows a slow moving truck (travelling at a speed of 10 m/s) on a two-lane two-way highway.…

Q: 40 KN # A B E |-5m—--5 m—-5m-5m C 60 kN.m F -10 m D

Q: In an engineering application, the material is a strip of iron with a fixed crystallographic…

A: This numerical can be solved by the Hall-Petch equation: According to Hall and Petch, iron and…

Q: A rigid container is partly filled with a liquid at 1520 kPa. The volume of the liquid is 1.232…

Q: Given a 1.0meter Wide Flange steel compression member with A=4071mm2, Ix=86842174mm4 and…

Q: Incorrect The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0).…

Q: : Find the max. compressive force (a)due to the following moving load.

A: ###Determination of maximum Compressive Force in member 'a' using influence line Diagram ####

Q: Determine the moment of inertia of the stringer cross section about the horizontal centroidal axis.

Q: What is the required diameter (in mm) for a sewer that will drain a catchment with 250 people? The…

Q: A town of 2 lakh population is getting water at the rate of 150 litres per capita per day from a…

Q: An irrigation channel is carrying 3.0 m³/sec of water to a culturable command area of 1500 ha with…

Q: A structural beam subjected to sagging bending has a cross section which is an unsymmetrical I…

Q: Q'-4a

A: Given data - Diameter of particles(d) = 0.10 mm Rate of flow(Q) = 0.10 m³/s gravity (g) = 9.81…

Q: 3.22 For the truss shown in Figure P3-22 solve for the horizontal and vertical components of…

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

Q: B-4 Determine the support reactions. Assume B is a pin and A and C are rollers. then draw the shear…

A: Given: Required: Support reaction, shear force diagram and bending moment diagram

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: A moving particle has a velocity described in the following data: 15 Time (sec) Velocity (m/s) 24 0…

Q: 3 kPa. Using f'c = 21 MPa, long bar fy = 415 MPa, calcu. Factored uniform load on a typical interior…

Q: Soil samples A and B have void ratios of 0.5 and 0.7 respectively. If 1.5 m³ of soil sample A and…

A: Given: Soil sample A: Void ratio, eA = 0.5 Volume, VA = 1.5 m3 Soil sample B: Void ratio, eB = 0.7…

Q: The pan evaporation for a particular month is 3 cm. The pan coefficient is 0.80. The lake…

A: Given- Pan evaporation=3 cm, Pan coefficient=0.80

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given To find Find the force in all member

Q: Design load: N=400kN, e-300mm Profile of the beam: Steel Grade: Q235B Electrode: E43 The weld leg…

A: Given Design load (N)=400kN Eccentricity (e)=300mm Size of fillet weld at flange=8mm Size of fillet…

Concept explainers

Volumes

Volume usually is the dimensional quantity that involves the evaluation of any three-dimensional figure enfolded inside a closed space. The SI unit (International System of Units) of volume is m3 and the dimensional unit of volume is [L3]. For estimation of the volume of any figure, various formulae are used. Another application of volume includes the reference in the sound levels, the higher the sound intensity, the louder the sound heard, and hence, the larger the volume. The SI unit of sound volume is decibels (dB).

Question

If an offset is laid out 3° from its
true direction on the field. Find the
Limiting length of offset (m) so that
the displacement of the point on the
paper may not exceed 0,25mm. The
scale of plotting is
1
5000

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the base angle at Slice 3 in the fgure below? a. 5o b. 16o c. -5o b. -16o
Determine the length of line EA. 1 decimal place
EXAMPLE 1: Draw the fallowing Figure using the different methods of ends line coordinates specifying. 80 60 30
Draw projections of the following two points A & B on the same XY line. Keep a gap of 50 mm between the two reference points that is a0 and b0.a) A point A is 20 mm behind VP and 40 mm above HP.b) A point B is 20 mm behind VP and 40 mm below HP.
please, pleaseeee can u help me plot the horizontal and vertical distance using free hand
Draw projections of the following two points A & B on the same XY line. Keep a gap of 50 mmbetween the two reference points that is a0 and b0.a) A point A is 20 mm behind VP and 40 mm above HP.b) A point B is 20 mm behind VP and 40 mm below HP.
Determine the y-coordinate of the centroid of the shaded area shown 7" Parabolic. 3" Answer: y = i tel 11x 5" in.
A point ‘B’ is located 30 mm below HP and 40 mm behind VP. Draw projections.
Compute the interior angle at A, B, C, D * B S 75° 15' E N62° 20' E A D Your answer
FIND THE SOLUTION (D3+7D² + 19D+13)y=D0 where x=0, y=o y'=2, y" = -12 %3D
ANSWER ASAP. WILL UPVOTE
b. Label the plot of the profile accordingly. The stationings, elevations, and horizontal and vertical scales must be indicated. Station BS HI FS IFS ELEV Remarks ВМа 0.95 500.95 500.00 Lamp post 10 +00 0.25 500.70 +10 0.44 500.51 ТР1 3.13 503.44 0.64 500.31 20+00 0.75 502.69 +10 0.89 502.55 +20 0.96 502.48 ТР2 2.16 504.32 1.28 502.16 30 +10 0.90 503.42 +20 1.10 503.22 BMb 1.00 503.32