If F = 730 lb, F = 380 lb, F 620 lb, determine the magnitude of the resultant force acting on the corbel. (Figure 1) Express your answer to three significant figures and include the appropriate units. FR = 1270 lb Submit Previous Answers v Correct Correct answer is shown. Your answer 1267 Ib was either rounded differently or used a different number of significant figures than required for this part. Figure < 1 of 1 > Part B Determine the direction 0 of the resultant force acting on the corbel measured counterclockwise from the z axis Express your answer to Caree significant figures and include the appropriate units. HA % A. 0 = 78.1 Submit Previous Answers Request Answer P Pearson Copyright ©2021 Pearson Education Inc. All rights reserved. I Terms of Use I Privacy Policy I Permissions I Contact Us I 4:21 PM 2021-02-25

If F = 730 lb, F = 380 lb, F 620 lb, determine the magnitude of the resultant force acting on the corbel. (Figure 1) Express your answer to three significant figures and include the appropriate units. FR = 1270 lb Submit Previous Answers v Correct Correct answer is shown. Your answer 1267 Ib was either rounded differently or used a different number of significant figures than required for this part. Figure < 1 of 1 > Part B Determine the direction 0 of the resultant force acting on the corbel measured counterclockwise from the z axis Express your answer to Caree significant figures and include the appropriate units. HA % A. 0 = 78.1 Submit Previous Answers Request Answer P Pearson Copyright ©2021 Pearson Education Inc. All rights reserved. I Terms of Use I Privacy Policy I Permissions I Contact Us I 4:21 PM 2021-02-25

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 35P

See similar textbooks

Similar questions

A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
Show complete solution with figures A rigid container having outside diameter of 30 mm and thickness of 5 mm contains water of height 700 mm.What will the column length be if a force of 5 kN is applied to its open end by a frictionless plunger? Assume noleakage. Use 2.2 GPa for bulk modulus of elasticity of water. a) 689 mm b) 525 mm c) 527 mm d) 695 mm e) None
A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’svolume is then 805.407 in3. If the water is released from the tank, how many poundswill be collected at atmospheric pressure? Use 305 000 psi as an average value of bulkmodulus of elasticity
Determine the value of Rb. a. 78.5 lb b.578 lb c. 785 lb d. 875 lb
Kindly give me right solution with clear calculations. A 1.40 m2 chunk of wood floats in oil. Wood has a specific gravity of 0.64, whereas oil has a specific gravity of 0.84. Calculate the amount of wood in cubic metres that will support a box weighing 34kg.
Show complete solutions. (2 decimal places) 1. Imagine the plumb bob as a perfect cone, compute for the volume of steel needed to make thecone if the dimension are a diameter of 60 mm and a height of 40 mm. The height of a cone shaped tank for liquid storage in a chemical factory is 9 ft with a diameter of14 ft. a) what is the volume of liquid the tank can hold in cubic feet? (5 pts); b) if the storage tankreleases water with a rate of 350 liters per minute, how many minutes will it take for the tank beemptied?
10. Situation 4 - A block of wood 0.6 m x 0.6 m x “h” meters in dimension was thrown into the water, it floats with 0.18 m projecting above the water surface. The same block was thrown into a container of a liquid having a SG of 0.90 and it floats with 0.14 m. projecting above the liquid surface. Determine the weight of the block in kN. Round off to three decimal places.
A wooden beam is loaded by a distributed load w = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1900 mm, LBC = 3100 mm, W=200 mm, B0 = 30 mm, and H = 200 mm, h0=20 mm. Units: use N, mm, MPa as consistent units for all calculations.
Use the Darcy's law to figure out the equation below, figure out what K is Q/A = K(dh/dl) 1.11/50.6 = K(4/36)
A tank containing water has a total of weight of 75 kg when weighed. Obtain the new reading on the weighing scale if a 50 mm by 50 mm piece is wood is held vertically in the water to a depth of 600 mm. a. 73.5 kg b. 76.5 kg c. 77.5 kg d. 78.5 kg
Please show step by step calculation of each value
Physics Take P = 180 lb. A) Determine the horizontal and vertical components of force acting on pin A. B) Determine the magnitude of the horizontal and vertical components of force acting on pin C. Express your answers in pounds to three significant figures.