If i cannot use ammonia water, what can i use as a substitute to make my acid supernatant to be an alkaline? After being macerated with 95% ethanol and dissolved in 5% acetic acid, I got an acid supernatant and I was supposed to use ammonia water along with dichloromethane but the ammonia water was disregarded due to specific reasons. What can I replace my ammonia water with to make my acid supernatant an alkaline?

If i cannot use ammonia water, what can i use as a substitute to make my acid supernatant to be an alkaline? After being macerated with 95% ethanol and dissolved in 5% acetic acid, I got an acid supernatant and I was supposed to use ammonia water along with dichloromethane but the ammonia water was disregarded due to specific reasons. What can I replace my ammonia water with to make my acid supernatant an alkaline?

Chemical Principles in the Laboratory

11th Edition

ISBN:9781305264434

Author:Emil Slowinski, Wayne C. Wolsey, Robert Rossi

Publisher:Emil Slowinski, Wayne C. Wolsey, Robert Rossi

Chapter20: Rates Of Chemical Reactions, I. The Iodination Of Acetone

Section: Chapter Questions

Problem 1ASA: In a reaction involving the iodination of acetone, the following volumes were used to make up the...

See similar textbooks

Similar questions

In order to analyse mercury with AAS, which method will you prefer? Explain this method in detail.
How is using thiamine as a catalyst rather than cyanide an application of greenchemistry? PROCEDURETo a six inch test tube was added thiamine hydrochloride (0.65 g), followed by water (2mL). The mixture was gently shaken until homogeneous, and then ethanol (7.5 mL)was added. Finally, sodium hydroxide (10%, 1.5 mL) was added and the mixture wasgently stirred to ensure complete mixing.Benzaldehyde (3.8 mL) was then added at room temperature in one portion with gentlestirring. The pH of the resulting reaction mixture was determined and adjusted to >10by dropwise addition of 10% sodium hydroxide. The reaction mixture was then partiallysubmerged in a 65 °C water bath2 and the progress of the reaction was periodicallymonitored by TLC analysis.Once TLC analysis indicated that the reaction was complete, the reaction mixture wascooled to approximately room temperature, and then chilled in an ice-water bath. Theresulting precipitate was collected by vacuum filtration and air-dried. The…
Volumetric Analysis The mass of KHC8H4O4 is measured to the nearest milligram; however, the volume of water in which it is dissolved is never of concern—water is even added to the wall of the Erlenmeyer flask during the titration. Explain why water added to the KHC8H4O4 has no effect on the data, whereas water added to the NaOH solution, may drastically affect the data.
8. A student was asked to find the acid and basic radicals in six simple salts provided to him labeled as A,B,C,D,E and F. When he examined them, he observed that sample B was blue in colour and the remaining five salts were white. Answer the following questions. a. Why is concentrated HCl used in performing the flame test and not any other concentrated acid? b. What clue does this blue colour give about sample B? c. What is the importance of a negative test in salt analysis? d. The student is aware that he has to classify the anions into groups. What is the basis of this classification? e. Describe one test which distinguishes a bromide ion from a nitrate ion. f. The student observed that when dil HCl was added to a pinch of sample A. it gave brisk effervescence which turned lime water milky, while sample E gave a gas with rotten egg smell with the same reagent. Identify the acid radicals in sample A and E from the above observation and write the balanced equations involved
Is a Kd value of 10.16 reasonable for the extraction of benzoic Acid between methylene chloride and water? Please explain.
1. Why is it necessary to use a buret for measuring standard AgNO3 solution in volhard method? 2. What is the effect of discolored AgNO3 on the concentration of KSCN? 3. Why is necessary to use boiled 6N HNO3 in volhard? 4. why is the titration done with vigorous swirling? 5. A solution of AgNO3 is added to a solution containing 0.100 Cl- and 0.100M CrO4-, at what Ag+ concentration will Ag2CrO4 begin to precipitate? and what will be the concentration of the less soluble compound when the more soluble one begins to precipitate?
In order to analyse mercury with AAS, which method will you prefer?
Considering the procedure below: “Determination of the concentration of HCl: Pipette 10 mL of hydrochloric acid and transfer to a 100 mL volumetric flask, complete the volume with water and homogenize. Remove a 10 mL aliquot of this solution and transfer it to a second dilution in a 100 mL volumetric flask, complete the volume with water and homogenize. Take a 20 mL aliquot of this last solution and transfer to a 250 mL erlenmeyr and add 20 mL of distilled water and 4 drops of the acid-base indicator. Titrate with a previously standardized 0.100 mol/L sodium hydroxide solution until the indicator turns.” Answer: a) In this titration, the indicator used is phenolphthalein. Discuss the use of this indicator considering its turning range and pH at the stoichiometric point of the titration. Justify. b) Considering that the volume of titrant used was equal to 24.5 mL, calculate the concentration of HCl in the sample in mol/L.
Calculate the molecular weight from the titration data. What does that suggest about how many nitro groups were added?
Which of the three methods, (Use of Separatory Funnel, Decantation or Use of Pasteur Pipette) do you believe is most suitable for transferring large volumes of liquid mixtures and why?
In a reaction involving the iodination of acetone, the following volumes were used to make up the reaction mixture: 5mL4.0M acetone+10mL1.0M HCl+10mL0.0050MI2+25mLH2O a. How many moles of acetone were in the reaction mixture? Recall that, for a component A, moles A=MAV, where MA is the molarity of A and V is the volume in liters of the solution of A that was used. __________ moles acetone b. What was the molarity of acetone in the reaction mixture? The volume of the mixture was 50 mL, 0.050 L, and the number of moles of acetone was found in Part a. Again, MA=moles ofAV of soln. in liters __________ M acetone c. How could you double the molarity of the acetone in the reaction mixture, keeping the total volume at 50 mL and keeping the same concentrations of H+ ion and I2 as in the original mixture?
Bleach (sodium hypochlorite, NaOCl, a strong oxidizing agent) neutralizes and inactivates mustard gas. Bleach is also effective on organic stains because it oxidizes coloredcompounds to colorless compounds. Propose products that might be formed by thereaction of mustard gas with bleach