If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given inputs as 1 1, then the input data will b sent to the output O a. Y1 O b. Y3 O c. YO O d. Y2
Q: Perform the following functions: a. What will be the parity of the data signal to send as even…
A: (a) When the data is checked for the parity, 0 is the output when there is even parity, and 1 is the…
Q: Implement a full adder using dual 4-input multiplexer Give stb1 and stb2 constant 1. Use ZX…
A: A Full Adder is a combinational logic circuit with 3 inputs : A,B,C and two outputs : Sum, Carry.…
Q: R1 Write Datap00O 1001 Read Data 1 DMX MUX R2 Write Register Read register number 1 R3 R4 Read Data…
A: The input of combinational circuit only depends on present input. Initially the values are 0 0 0 0.…
Q: If the four input lines of a multiplexer are DO, D1, D2 and D3, and the two select lines are given…
A: Four input lines of a multiplexer, and input for the select lines are 11 then find the output of…
Q: Q4: Write the correct statement : 1. Convert the character "D"in Al to lower case. 2. Jump to…
A: Write the correct statement : 1. Convert the character "D"in Al to lower case. 2. Jump to…
Q: Byusing Lop' instruction, Save the number of ones inside Dx regisder ex) if DX=1 2 34 h (oool oolo…
A:
Q: Write a Boolean expression for the 4 to 1 digital multiplexer with data input ABCD and address…
A: to write a Boolean expression for the 4 to 1 digital multiplexer with data input ABCD and address…
Q: Identify the state diagram operation and find its output sequence for the following input sequence:…
A: Given circuit is: It has two states S0 and S1. The input sequence is: X = 0101 1100 0101 0000
Q: What is ADC resolution? If the input voltage range (input voltage range) is Vrange = 15 volts and…
A:
Q: A 3-bit quantiser has a dynamic range of ±4 Volts. How many quantisation levels could this system…
A: Given, Number of bit in quantiser, n=3 Dynamic range, ±4 V
Q: Fill-in the tables below with different representations of a number. Decimal Binary Hexadecimal 154…
A: Digital electronics
Q: Write an instruction that stores a double-word value
A:
Q: the use of which function in a sketch has significant drawbacks. No other reading of sensors,…
A: We have to tell in the given Ardunio codes the function which has significant drawbacks. No other…
Q: If the four output lines of a demultiplexer are YO, Y1, Y2 and Y3, and the two select lines are…
A: In this question , we will write output selected for select lines 1 1...
Q: Designthe following using only one 4:1 Digital Switch, in which K and M are the data inputs. Z(KLMN)…
A:
Q: Q2) Compute the physical address for the specified operand in each of the following instructions;…
A:
Q: A multiplexer is a device that selects one among N analog or digital inputs and forwards the…
A:
Q: It is required to generae a time delay of 7 ms on P2.2. What will be the value that required to load…
A: Time delay required 7 ms, crystal frequency = 10592 MHZ,
Q: Enter the following data patterns and record the outputs. Input Switches D. 14 +5V 7495 B • 2 4 Bit…
A: The Parallel-In Parallel-Out shift register is a type of data storage device. This is commonly…
Q: What is the content of the accumulator after executing each of the following instruction should be…
A: When we execute following 8051 assembly instructions. MOV A,#0ABH The value 0ABH move into…
Q: 1- In data presentation system, calibration is ___________________. a. putting a heavy object on…
A: In data presentation system, calibration is comparing the output of a measurement system and its…
Q: Q1.A. A sequence detector has an input w and an output z. The machine is a sequence detector that…
A: Moore machine: A Moore machine is a finite state machine whose output is always based on the…
Q: 11. At TO the content of the register is 0000. What is the content of the register at T1? T4 T3 T2…
A:
Q: to Calclate the write an 8085 micro Pro e ssor program number of negative data am ng Ahe flbwing clu…
A: We have to write programming code to calculate the number of negative data among following data. (…
Q: You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX,…
A: The instruction DEC BX has the address 1369:0106, the given address consists of segment address and…
Q: Q4/The initial content of the 4-bit serial-in-parallel out right shift register shown in figure 3 is…
A: In the question We are determine the content of the shift register after 4 cycle.. All are D flip…
Q: F = A'B + B'C + C'D Implement the function F using: a. one 16X1 multiplexer b. one 8X1 multiplexer…
A: Since you have posted a question with multiple subparts, we will solve the first three subparts for…
Q: If a DIP switch with 8 switches (0-7) lines up with bit0-7 of the data bus, and switches 1,2,4,5 & 7…
A: In this question, We need to choose the correct options If switches 1,2,4,5 & 7 are set then…
Q: Q2: (A)- Write A program that computes Z-1(CL)*+(CH)'J/BL, places the result (Z) in the BX register.…
A: The program is as follows
Q: Q4/The initial content of the 4-bit serial-in-parallel out right shift register shown in figure is…
A:
Q: Design a 4 bit register that will be able to perform the following commands. si s2 Register…
A: Given: Command table: To find: Design a 4-bit register that will be able to perform the following…
Q: Choose the instruction that will clear (makes zero) the contents of CX register. Assume that CX has…
A: Outpot of NOT gate is complement of input. Output of AND operation is 1 when both inputs are 1.…
Q: Find the data inputs of the following multiplexer that implement the function F. F(A,B,C.D.E.F)=…
A: The boolean expression for the multiplexer input can be obtained from the truth table and by using…
Q: Q3: Assume that you have to spread two signals A and B, using CDMA with the DSSS. The data of…
A:
Q: Choose the proper signal to drive each input such that the output F = (X'.Z + X'.W + Y.Z) %3D 1 8X1…
A: We need to find out the input for multiplixer input for given logic function .
Q: You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX,…
A: The instruction is loaded at location 0106, the instruction takes two bits when the given code is…
Q: If the SHIFT/LOAD line is LOW, data a. is loaded from Do, D1, D2 and D3 immediately b. is loaded…
A: A simple problem on digital electronics . Look below for solutions:-
Q: Q2. Construct the Mealy and Moore state diagrams for a sequence detector that outputs a 1 when the…
A: In a sequence detector the output is 1 when the sequence is detected. In Mealy circuit the output is…
Q: It is required to generae a time delay of 7 ms on P2.2. What will be the value that required to load…
A:
Q: Design a-full subtractor with two multiplexers (MUXS) S(x.y.2) = E( ... ), Cay2)Σ(... ).| Connect…
A:
Q: Q1- c) Several ID Automation products support the inclusion of the Application Identifier(Al) with…
A: Application Identifiers (AIs) are numeric prefixes that specify the meaning and syntax of encoded…
Q: D1 Q1 Do Qo CLK- Qo If the circuit above is a set of sensors, which of the following is the output…
A:
Q: Electrical Write verilog Algorithm level code for 4:1 multiplexer
A: Multiplexer is combinational Circuit that select one of its input to the output . The select line…
Q: Q4/The initial content of the 4-bit serial-in-parallel out right shift register shown in figure is…
A: Initial value 0011 What will be content of the shift register after 4 clock . We know D flip flop…
Q: Consider the situation for numbers 22 to 25, The information in an analog waveform with maximum…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: :What will be the contents of register BL after the last instruction execution? MOV BL, 14H MOV CL,…
A: SHL instruction shift left the bits of BL . The MSB is shifted into carry flag CF and LSB is filled…
Q: Q. 3 For the following 4-bit shift register draw complete the timing diagram if the input (Data_in)…
A:
Q: In a multiplexer with n input bits, how many output bits are there? О а. 1og n of O b. n O c. None O…
A: In this question we will write about multiplexer....
Q: Write the contents of AL and BL register after execution of the program MOV AL, FFh MOV BL, AL CMP…
A: The given instructions are of 8086 microprocessor, we need the to write the content of registers AL…
Q: How many data control lines are required if a multiplexer has eight inputs? a. 8 b. 4 c. 2 d. 3
A:
Step by step
Solved in 2 steps with 2 images
- You want to design a grading machine. The input is 3-bit score (0-7). The output is a 7-seg controller that shows the grade. You want to display A. when the score is 7 B. when the score is 5,6 C. when the score is 3,4, D. when the score is 1,2 F. when the score is 0The following sequence iof bits(right most bit first) appear on the inputs to a 4 bit parallel adder .Determinre the resulting sequence of bits on each sum output. A1 1101 A2 1110 A3 0000 A4 1011 B1 1111 B2 1100 B3 010 B4 0010A binary multiplier is given 10102 and 10112 as inputs. Calculate the binary output of the circuit. An octal multiplier is given 258 x 168 as inputs. Calculate the octal output of the circuit.
- Write an assembly code that will calculate the value of y in the following equation: y=-239 y= 2*20+ 3*19−4*84=-239 Here, roll= 2019000510084 please help me with those questions, those are from – Microprocessor and Interfacing, Electrical and electronics engineering.Determine output logic clear but clear buble are inversions the black dots are nodesDefine MUX and DEMUX. Where we use mux and demux system? How toc reate a 16:1 MUX by using 4:1 MUX with a truth table and draw a diagram for this MUX
- Convert both numbers into binary form then construct to circuit in order to calculate the result “S” for the operation given below. Assume that no Carry was available initially. S=1453-1071 Thank you :)Q4: Simplify the following Boolean expression using K-Map x'z+w'xy'+w(x'y+xy') (check image for reference)a) set the logical expression with ANDNOT gates b)Set up the logical expression with OR NOT gates. first photo is a second photo is b
- design a two-way traffic light system with prototype using 4-bit down counter circuit. use 7-segment as an output to represent the timer.i need help.. pls make a circuit diagram for this. i will do this on the breadboardand also explain how u did it. thank youthe photo attached is how i will do itQ2 Perform the following conversions:a) Converting (756.603)8 to hexb) Converting A0F9.0EB to decimelc) (1001010)2 to grayd) (163.875)10 to binarye)0110 BCD to excess -3Plot x2e(t) + x2o(t) and verify that x2e(t) + x2o(t) = x2(t). (Signal is included.)