Identify the state diagram operation and find its output sequence for the following inputsequence: X 0101-1100-0101-0000. The circuit accepts input bits from LSB to MSB.0/1 or 1/0X/Z=0/01/1SOS1(a) 2's compliment, Z= 1010-0011-1011-0000.(b) Mealy Machine, Z= 0110-0011-1010-1111.(c) Moore Machine, Z 1010-0011-1011-0000.(d) Serial adder, Z 0110-0011-1010-1111.Answerrealme Shot by Gowthamnag2021/10/30 15:28

Given circuit is: It has two states S0 and S1. The input sequence is: X = 0101 1100 0101 0000

Identify the state diagram operation and find its output sequence for the following input sequence: X=0101-1100-0101-0000. The circuit accepts input bits from LSB to MSB. 0/1 or 1/0 X/Z=0/0 1/1 SO Si (a) 2's compliment, Z= 1010-0011-1011-0000. (b) Mealy Machine, Z=0110-0011-1010-1111. (c) Moore Machine, Z= 1010-0011-1011-0000. (d) Serial adder, Z= 0110-0011-1010-1111.

Identify the state diagram operation and find its output sequence for the following input sequence: X=0101-1100-0101-0000. The circuit accepts input bits from LSB to MSB. 0/1 or 1/0 X/Z=0/0 1/1 SO Si (a) 2's compliment, Z= 1010-0011-1011-0000. (b) Mealy Machine, Z=0110-0011-1010-1111. (c) Moore Machine, Z= 1010-0011-1011-0000. (d) Serial adder, Z= 0110-0011-1010-1111.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter9: Components For Electric Motors

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

pls help me in these questions pls write the questions with the and by (Computer) 1- In data presentation system, calibration is ___________________. a. putting a heavy object on the measurement device. b. compressing spring of indicators in one direction. c. connecting a load across the output terminals of any element of a measurement system. d. comparing the output of a measurement system and its subsystem against standards of known accuracy.================ 2- The following explains the process that can occur in conditioning a signal.I. Protection to prevent damage to the next element.II. Getting the signal into the right type of signal.III. Getting the level of the signal right.IV. Eliminating or reducing noise by amplifying the signal.V. Manipulating a signal e.g. making it a linear function. a. All the answers. b. III, IV and V. c. I, II and IV. d. I, II, III and V.=============3- Based on the figure below, which of the following statement is INCORRECT in…
Q.The outputs of four registers, A, B, C, D, H, L are connected through 8:1 line multiplexer to the input of a fifth register. X. Each register is 16 bits long. The required transfers are dictated by four timing variables. To through T3 as follows: TO: X-A T1: X-B T2 : X-C T3: X-D The timing variables are mutually exclusive, which means that only one variable is equal to 1 at any given time, while the others are equal to 0. Draw a block diagram showing the hardware implementation of the register transfers. Include the connections necessary from the four timing variables to the selection inputs of the multiplexers and to the load input of register X.
If a DIP switch with 8 switches (0-7) lines up with bit0-7 of the data bus, and switches 1,2,4,5 & 7 are set, what value is read into the AL register (a) 6D (b) D6 (c) 6B (d) B6
SP=1236, AX=24B6, DI=85C2, and DX=5F93, show the contents of the stack as each instruction is executed. PUSH AX PUSH DI PUSH DX
Draw a dataflow circuit using block components that lets you add or subtract two input numbers in all possible ways. Your circuit will have two inputs X, Y and one output Out. You’ll have an adder and you’ll need to use multiplexers on each input to the adder. Clearly specify the number and type of control bits needed.
23 In the shift register given in the figure, there is a sequence of 1010 bits at the start time. The leftmost bit is used as MSB, and the rightmost bit is used as LSB. At each rising edge of the clock signal, the bit sequence is shifted one bit to the right. Accordingly, after how many clock ticks will the bit sequence in the shift register become 1010 again? saat sinyali = clock signal seri giriş = serial input
Question : with Eight LEDs with 74HC595. This code uses a shift register to use a single data pin to light up 8 LEDs. The code uses the command "bitSet" to set the light pattern. What is the value of the variable leds when the value of currentLED is 5? Hint: You can use Serial.begin(9600) in the setup and Serial.println(leds) in the loop to examine this value. Answer must be a numerical value
Please try this question It's is digital signal processing question
What will be the modified form of the following codeword is odd parity scheme is used: Codeword: 0110101
If al is set to Ox05 and ax is set to 0x0007, eax is set to 0x00000020, and rax is set to Ox0000000000000000, and show the final complete contents of the complete rax register.
What will be the value of after implementing Circular shift right once A1, where A1 is equal 1100 1110 0110 0111 1001 1101 1001 1100 0011 1000
Please answer in detail. The outputs of four registers, A, B, C, D, H, L are connected through 8:1 line multiplexer to the input of a fifth register, X. Each register is 16 bits long. The required transfers are dictated by four timing variables, T0 through T3 as follows: T0 : X←A T1 : X←B T2 : X←C T3 : X←D The timing variables are mutually exclusive, which means that only one variable is equal to 1 at any given time, while the others are equal to 0. Draw a block diagram showing the hardware implementation of the register transfers. Include the connections necessary from the four timing variables to the selection inputs of the multiplexers and to the load input of register X. Note - Each register is 16 bits long and there are 8:1 multiplexers.