If the machine is running at 1500 r.p.m. and the armature has 16 conductors per each slot. Assume that the generated voltage in each conductor is 3 volts and each one can carry a full load current of 2A (the machine is separately excited). Determine: vi) The terminal voltages on no-load. The output current on full-load. The required flux per pole. vii) viii) The power developed by the armature on full load and then;

If the machine is running at 1500 r.p.m. and the armature has 16 conductors per each slot. Assume that the generated voltage in each conductor is 3 volts and each one can carry a full load current of 2A (the machine is separately excited). Determine: vi) The terminal voltages on no-load. The output current on full-load. The required flux per pole. vii) viii) The power developed by the armature on full load and then;

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An 6 pole, wave connected armature has 520 conductors and its generated e.m.f is 125 V. If the machine is driven at 400 rpm, then the flux per pole in Wb is,
22 The DC voltage is generated in the Armature winding of DC Generator. Select one: True False
A 230 V dc machine has an emf constantand . The field is separatelyexcited and produces 0.01 Wb per pole. for all parts ofthe problem. (a) At what speed does the machine operate as adc generator with rated terminal voltage? (b) At what speeddoes the machine operate as a dc motor with rated terminalvoltage? (c) If an external resistance is added in serieswith the armature circuit, at what speed does the machineoperate as a dc motor with rated terminal voltage? (d) If themotor of part (b) is known to be supplying 10 HP to a coupledmechanical load, determine the rotational losses at the point ofoperation ***Any two branches please do not be late
111/ The armature reaction of the DC generator reduces the generated EMF. Select one: True False
The armature of a dc motor has 648 conductors, 65 % of which are directly under the pole where the flux density is 48,000 lines per in2. If the core diameter is 7 inches and its length is 4 inches and the current in each conductor is 20 A. What is the torque exerted in the armature in N-m?
DC MACHINE TORQUE The armature of a dc motor has 648 conductors, 65 % of which are directly under thepole where the flux density is 48,000 lines per in2. If the core diameter is 7 inchesand its length is 4 inches and the current in each conductor is 20 A. What is thetorque exerted in the armature in N-m?
(Draw the Circuit Diagram) A self-excited shunt generator has a field resistance of 60 ohms. When the generator delivers 6 kW, the terminal voltage is 120 V, while the generated emf is 133 V. Determinethe armature resistance
A 3-phase, 2-pole-pair, induction machine operates at 1450 revolutions per minute when fed from a 50Hz supply at 240rmsV phase voltage. If the air-gap flux linkage of the machine is kept approximately constant when the supply frequency Is 41 Hz, the rms phase voltage of the machine should be ?
a) How laminated core of electrical machines reduces the iron losses?b) How can you control the voltage of dc generator during operation?c) Why parallel paths are used in electrical dc machines?
A 220 V dc machine has an armature resistance of 1ohm if the full load current is 20 A, the difference of induced voltage, when the machine is running as a motor and generator, is *
- A separately excited 4 - pole, 900 rpm wave wound dc generator has an induced emf of 240V at rated speed and rated field current. When connected to a load, the terminal voltage is observed to be 200V. If the armature resistance is 0.2 Ω and the flux per pole is 10 m Wb, compute the armature current and the number of conductors
A 1500 kW, 550 V, 16 pole generator runs at 150 rev. per min. What must be the useful flux if there are 2500 conductors lap-connected and the full-load copper losses being 25 kW? Calculate the area of the pole shoe if the gap density has a uniform value of 0.9 wb/m2 and find the no-load terminal voltage, neglecting armature reaction and change in speed.