If the settling time (2% criterion) and the peak time of a 2nd order system are given, find the location of the 2 closed-loop poles on the s-plane. Type a, b, c or d.王手手干t; = 7 sec and wn = 1.195 rad/sec.jws-planejws-planejws-planejws-planeXj2.047X---j1.047X-j0.57X-j0.57-2.047- 1.57-0.57-1.047X(а)(b)(c)(d)Answer:

Given the settling time is ts=7sec For, 2% tolerance, the settling time is given as, ts=4ξωn Hence,…

If the settling time (2% criterion) and the peak time of a 2nd order system are given, find the location of the 2 closed-loop poles on the s- plane. Type a, b, c or d. ts = 7 sec and wn = 1.195 rad/sec. 年平丰キ j , s-plane jw s-plane jw s-plane jw s-plane X j2.047 X.-- j1.047 X-- j0.57 X- j0.57 -2.047 - 1.57 -0.57 -1.047 X X X (a) (b) (c) (d) Answer:

If the settling time (2% criterion) and the peak time of a 2nd order system are given, find the location of the 2 closed-loop poles on the s- plane. Type a, b, c or d. ts = 7 sec and wn = 1.195 rad/sec. 年平丰キ j , s-plane jw s-plane jw s-plane jw s-plane X j2.047 X.-- j1.047 X-- j0.57 X- j0.57 -2.047 - 1.57 -0.57 -1.047 X X X (a) (b) (c) (d) Answer:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.23MCQ

See similar textbooks

Similar questions

A ) Calculate the control poles S1 and S2 where the settling time is t=4 s according to the criteria Mp=5% (Mp=0.05) and 2% of the exceedance in the closed-loop control system with the root locus given on the side. B) Interpret the stability of the minimum phase systems for which Nyquist diagrams are given below.
Write any four methods of voltage control and Draw the basic block diagram of AC – DC transmission system. and A transmission line has a span of length 250 m and the weight of the conductor per metrelength is 0.63 Kg. The tension in the conductor is 1250 Kg. Calculate the sag and heightabove the ground at which the conductor should be supported. Consider the groundclearance required is 13m
i. Sketch the pole-zero diagram and specify the ROC for H(z). ii. Determine if the system is stable or not?
Given a four pole IM connected to a 50-cycle 3 phase circuit. Calculate the airgap diameter (rotor diameter), given that the peripheral velocity at synchronous speed is 3500 fpm. (ILLUSTRATIONS such as diagrams and graphs are Required).
Using the Routh-Hurwitz criterion, tell how many closed loop of the system shown in Figure 2 lie in LHP, RHP and jω axis.
a) Calculate the si and s₂ control poles where the settling time is Ts=4 seconds according to the criteria Mp=5% (Mp=0.05) and 2% of the exceedance in the closed-loop control system with the root locus given on the side.
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
Give a brief explanation onWhy isn't elapsed time a useful indicator of performance?
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the rated current will the inrush current be when the ASM is started directly?
An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
For the power system of Figure Q4.1, all per unit quantities have been calculated using a common base. The generator delivers power ??∞=1 ??.??. at a lagging power factor of ????????=0.93. i) Calculate the internal voltage of the generator, the maximum electrical power that the generator can deliver to the system during the steady state operation and the steady state rotor angle, ??0, of the generator.ii)A three-phase fault occurs at busbar 3 and it is cleared by simultaneously disconnecting lines 13 and 23. Following the fault clearing, the system continues to operate with only line 12 in service. Determine the new steady state rotor angle, ??1, of the generator and the maximum power the generator can deliver to the system post fault.iii)Assuming that the post fault condition is small disturbance stable and that there is no negative interaction among system controllers, calculate the critical clearing angle, ??????, at which the fault should be cleared to ensure the generator reaches…
The diameter of the overhead lines in the form of cylindrical conductors in a 300 kV three-phase transmission system is 20 mm.a) - How much distance should there be between two conductors using the maximum area calculation equations?Calculate. (Puncture peak strength of air is 30kV / cm.)b) - In this configuration, if the distance between phase conductors is 0m, at what voltage levelCalculate the discharge occurs?c) - Maximum electric field in the same configuration, for electrode distances to be 0mCalculate the value. If needed in calculations Ꜫ0 = 8.854x10-12 F / m)