Answered: , If the shown pipe is subjected to the…

, If the shown pipe is subjected to the two force components at its end as shown, determine the state of stress at point A on the cross section of the pipe at section a-a.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The pin support is made from a steel rod and has a diameter of 20 mm. Determine the stress…

A: Given data for the problem is : The radius of the steel rod is r = 10 mm. The load applied on the…

Q: If the cross section of the femur at section a–a can be approximated as a circular tube as shown,…

A: Considering the equilibrium of femur,

Q: The rotor shaft of the helicopter is subjected to the tensile force and torque shown when the rotor…

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

Q: Determine the state of stress at point A on the cross section of the member at section a-a.

Q: The steel pipe AB has a 72mm outer diameter and a 5mm wall thickness. Knowing that the arm CDE is…

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B,…

A: d=1in Draw the free diagram of the problem by converting the eccentric loads into the loads and…

Q: Determine the principal stress at point A on the cross section of the hanger at section b-b. Specify…

Q: Determine the maximum normal stress that loading produces in the steel member.

Q: Determine the maximum principal stress (Omax) at point H (MPa). she If th

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w) = 10 lb-ft the FBD of the cut segment of the rod is…

Q: Determine the maximum and minimum stress intensities set

Q: Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension…

Q: The steel tube below has an inside diameter of 2.75”, and an outside diameter of 3”. If the tube is…

A: The polar moment of inertia of the bar can be determined as,

Q: *134. The tank af the air compressor is subjected to an in- ternal pressure af 0.63 MPa. If the…

A: Given Data: The internal pressure in the cylinder is: P= 0.6 MPa. The thickness of the wall is: t=…

Q: The assembly consists of two sections of cast-iron rod connected together using a reducing coupling…

A: (a) To find: The maximum shear stress developed in each section. Given: The length of AB is lAB=12…

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the…

Q: The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress…

A: Given: The diameter of rod is D = 1 in. The weight of the rod is M = 15 lb/ft. The length of the…

Q: Determine the average punching shear stress the circular shaft creates in the metal plate through…

A: Given data: The value of shear load is F=40 kN The diameter of shaft is dAB=50 mm The thickness of…

Q: The shaft has a diameter d and is subjected to the loadings shown. Determine the principal stresses…

A: Given: The load acting at the centre of the shaft is P. The the axial force acting on the shaft is…

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: element, the normal and shear stresses gure. Determine the normal and shear el to the xy axes; that…

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Write the given data: Understand the effects of the 20 lb force on the member CD as shown in the…

Q: Es atmospheric. Determine (a) the radial and tangential stress distribut across the the thickness,…

A: a = 8cm, b=12cm, Pb = -0.09MPa

Q: kN, determine the magnitudes of the average normal stress in the shank, the average shear stress…

Q: Determine the state of stress at point A on the cross of the pipe at section a-a. Show the results…

Q: Determine the average normal stress developed in rod AB if the load has a mass of 64 kg. The…

Q: The propeller shaft of the tugboat is subjected to the compressive force and torque shown. If the…

A: Given Data: The inner diameter of the shaft is d = 100 mm. The outer diameter of the shaft is D =…

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point A,…

Q: The clamp presses the smooth surface at E when tightening the screw. If the tension in the bolt is…

A: Given data as per question Tension in the bolt =40 kN Support reaction are shwn on FBD (a)Internal…

Q: The block is subjected to the eccentric load shown. Determine the normal stress developed at points…

Q: at A. Determine the stress in AC and the horizontal and vertical components of the reaction at B.

Q: The steel rod has a circular cross section. If it is loaded by a 500 lb vertical force as shown,…

Q: The solid cylinder having a radius r is placed in a sealed container and subjected to a pressure p.…

A: Explanation: ◆ The solid cylinder is subjected to a pressure p inside the sealed cylinder. ◆ The…

Q: : The rod weighs 22 lb/ ft and has a diameter of 3 in. Determine the torsional stress at points A…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a-a.

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: Determine maximum principal stress

Q: Determine: a. The shear stress at point B on the web of the cantilevered strut at section a - a. b.…

Q: If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress…

Q: ed to the force as shown int e the maximum stress in

Q: d) Draw Mohr's circle of stress for the shaft and from this determine the principal stresses,…

Q: Determine the normal stress o (MPa).

A: Given: σx=67.3 MPaσy=25.5 MPaτxy=-24.3 MPaα=48.3°To determine:Normal stress σt

Q: Q#5: Given the state of stress shown, determine the stress components acting on the inclined plane…

Q: The state of stress at a point is shown on the element. Determine (a) the principal stresses and (b)…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

di (mm)=15 do (mm)=30 F1 (N)=300 F2 (N)=450

, If the shown pipe is subjected to the two force components at its end as shown, determine the
state of stress at point A on the cross section of the pipe at section a-a.
300 mm
4r
300 mm
3.t
do
200 mm
Section a-a
F,
F,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C and subjected to the horizontal 20-lb force acting on the handle of the pipe wrench, determine the principal stresses in the pipe at point B, which is located on the surface of the pipe.
The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe.
The beveled gear is subjected to the loads shown. Determine the stress components acting on the shaft at point B, and show the results on a volume element located at this point. The shaft has a diameter of 1 in. and is fixed tothe wall at C.
The beveled gear is subjected to the loads shown. Determine the stress components acting on the shaft at point A, and show the results on a volume element located at this point. The shaft has a diameter of 1 in. and is fixed tothe wall at C.
The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state of stress at point B on the cross section of the drill bit at section a–a.
The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does not rotate while subjected to a force of 75 lb, determine the principal stresses on the cross section at point C.
The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state of stress at point A on the cross section of the drill bit at section a–a.
Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.
The bent shaft is fixed in the wall at A. If a force F is applied at B, determine the stress components at points D and E. Take F = 13 lb and θ= 45 degrees a) Determine (σD)y b) Determine (τD)yx c) Determine (σE)y d) Determine (τE)yz
The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe.
The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm2 and 8 mm2, respectively. If d = 1 m, determine the average normal stress in each rod.
The steel tube below has an inside diameter of 2.75”, and an outside diameter of 3”. If the tube is fixed at C, and subjected to the 20 lb horizontal force acting on the wrench as shown, determine the principal stresses in the point A, which is located on the surface of the tube