200 lb X. 8 in. 3 in. 75 lb 125 lb

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: a) The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20…

A: Given data  outer diameter of pipe (do) = 28 mm  inner diameter of pipe (di) = 20 mm diameter of rod…

Q: If the cross section of the femur at section a–a can be approximated as a circular tube as shown,…

A: Considering the equilibrium of femur,

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each…

A: Given Data: The outer radius of the cylinder is: rO=47 mm The force exerted on the walls is: P=2…

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B,…

A: d=1in Draw the free diagram of the problem by converting the eccentric loads into the loads and…

Q: f F1 = 1070 lb and F2 = 2095 lb, determine the magnitude of the normal stress produced at point H.…

A: Given that ,  F1=1070lbF2=2095lb

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: Determine the maximum normal stress that loading produces in the steel member.

A:

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Since the magnitude of the direct shear stress compared to the twisting and bending stresses is very…

Q: vertical beam the maximum Stresses forces of the cross are applied to a shown. Determine. secion D…

A: Given: The load, P = 9.25 kN

Q: The square steel plate has a thickness of 10 mm and is subjected to the edge loading shown.…

A: Given data as per the question Force =50×0.2 = 10N Steel plate thickness = 10mm Θ =20 from vertical…

Q: The assembly consists of three stainless 304 steel alloy rods (G = 193 GPa) and a rigid cap G. If…

A:

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points C and D…

A: Determined the projection area of the signboard. Find the wind force

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: The 1/2-in.-diameter bolt hook is subjected to the load of F = 150 lb. Determine the stress…

A:

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points A and B…

A: Given Load = 1.5 KPa To find Stress component at point A and B with representation of result on a…

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w)    = 10 lb-ft the FBD of the cut segment of the rod is…

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: The square steel plate has a thickness of 10 mm and is subjected to the edge loading shown.…

A: We are authorized to answer one question at a time, since you have posted two questions so we are…

Q: Determine the stress components acting on the plane AB. Solve the problem using the method of…

A:

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A:

Q: The 200-mm-diameter aluminum cylinder supports a compressive load of 300 kN. Determine the average…

A:

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the inner diameter…

A: Write the given data: Understand that the stress generated at point A will be the tangential stress…

Q: The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress…

A: Given: The diameter of rod is D = 1 in. The weight of the rod is M = 15 lb/ft. The length of the…

Q: The solid rod is subjected to the loading shown. Determine the state of stress at point A, and show…

A: Given data: The force in x direction is Fx = 100 kN. The force in y direction is Fy = 10 kN. The…

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The 1/2-in.-diameter bolt hook is subjected to the load of F = 150 lb. Determine the stress…

A:

Q: The solid rod is subjected to the loading shown. Determine the state of stress at point B, and show…

A: Given data:

Q: A bar having a square cross section of 30 mm by 30 mm is 2 m long and is held upward. If it has a…

A: Compressive stress        σc=mgcosθA=5×9.81×2×cosθ0.032=109000 cosθ Taking moment…

Q: The spreader bar is used to lift the 2000-lb tank. Determine the state of stress at points A and B,…

A: Given data as per question weight of tank =2000 lb ∑Fy=02000−2Fcos30=0F=1154.7 lbInternal forces and…

Q: Determine the average normal stress developed in rod AB if the load has a mass of 64 kg. The…

A:

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point A,…

A:

Q: Determine the stress at points A and B, (a) for the loading shown, (b) if the 60-kN loads are…

A: The given loading condition is centric.

Q: The solid cylinder having a radius r is placed in a sealed container and subjected to a pressure p.…

A: Explanation: ◆ The solid cylinder is subjected to a pressure p inside the sealed cylinder.  ◆ The…

Q: : The rod weighs 22 lb/ ft and has a diameter of 3 in. Determine the torsional stress at points A…

A:

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A: The given beam is subjected to three loads- axial load, shear load and bending moment. Therefore…

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points A and B…

A: Point A:             σA=McI=10.5×103×0.05π40.054=107 MPa               τA=TcJ=3×103×0.05π40.054=15.3…

Q: Q5: Determine the average normal stress developed in rod AB if the load has a mass of 50 kg. The…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: The member is to be made from a steel plate that is 0.25 in. thick. If a 1-in. the hole is drilled…

A: Calculate the approximate width w of the plate…

Q: 3. FOR THE STATE OF STRESS SHOWN, DETERMINE THE STRESS COMPONENTS ACTING ON THE INCLINED PLANE A--A.…

A:

Q: If the block is subjected to a centrally applied force of P = 6 kip, determine the average normal…

A: The area of the cross-sectional = 14(6)-2(1)(4)=76 in2 σavg=PAσavg=676=0.0789 ksiσavg=PA=78.95 psi

Q: If the load has a weight equivalent to 5 kN, determine the maximur hormal stress on the cross…

A: Given Data Load is :P=5 kN=5000 N Radius of circle is :r=2 cm=20 mm Distance of CD is : LCD=50…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

A:

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. The pipe is fixed at…

A:

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: The free body diagram of the system is as follows.

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: A drilling machine is used to drill in-wall or furniture. To analyze the drill bit stresses we first…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.