Water flows into the atmosphere from a nozzle and strikes a vertical plate as shown in Figure Q2. A horizontal force of 10 N is required to hold the plate in place. Assume the flow to be incompressible and frictionless. The density of water is 998.2 kg/m³ and gravity effect is negligible. (b) (c) Determine the inlet and outlet velocities of the nozzle. Determine the pressure gage reading. If the water mass flow rate is doubled, (i) What is the minimum horizontal force required to hold the plate in place? Is there any changes to the reading of the pressure gage? (ii) Please justify your answer with proper calculations.

Water flows into the atmosphere from a nozzle and strikes a vertical plate as shown in Figure Q2. A horizontal force of 10 N is required to hold the plate in place. Assume the flow to be incompressible and frictionless. The density of water is 998.2 kg/m³ and gravity effect is negligible. (b) (c) Determine the inlet and outlet velocities of the nozzle. Determine the pressure gage reading. If the water mass flow rate is doubled, (i) What is the minimum horizontal force required to hold the plate in place? Is there any changes to the reading of the pressure gage? (ii) Please justify your answer with proper calculations.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
An industrial fan delivers 55,000 CFM of air through a discharge duct with a size of 3 ft x 4 ft where the static pressure is 6-inch water gage. At the inlet, the duct diameter is 4 ft and the static pressure is 1-inch water gage. The temperature of the air is 78 F and barometric pressure is 14 psia. (ρw = 62.2 lb/ft³). Determine: a). the total pressure in feet of air b). the static power in HP c). the fan power in HP
A certain turbine has a capacity of 45 ft³/s. 3ft³/s is lost during the flow. The tailwater is 14 7 ft from the center of the turbine. The intake measures 35 in and the pressure is measured by mercury u-tube manometer which measures 15.566 ft in the intake and 3.00 ft in the discharge side. The datum of the scale is at 5.62 ft below that of the center of the turbine. The brake power output was 767.8 kw. Losses is measured to be 20.2 KW. Calculate the efficiency of the turbine
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m
Water enters a house through a pipe with an inside diameter of 20 mm at an absolute pressure of 4 ATM. A 10 mm diameter pipe leads to a second-floor bathroom 5.0 m above. When the flow speed at the inlet pipe is 4 m/s, (a) Find the speed of the water flow and pressure in the bathroom. (b) Find the volume flow rate in the bathroom. (c) What is the horse power rating of the motor pump at the inlet pipe needed? Assuming 60% Efficiency.
Air flows through a compressor under steady flow conditions. At suction V1=0.75m3/kg, v1=30m/s At discharge: V2=0.25m3/kg, v2=40m/s.. Determine the diameter ratio of the discharge pipe to that of the suction pipe. (Ans. 1:2)
The density of the liquid striking the "splitter" of Figure 6.15 is 830 Kg/m. Dėtermine the force components of the force on the splittèr. Assume a smooth entry / sliding of the stream of liquid. (10) 2 số° Fy 2 Fx cs 30 Q,-0.03 cms Vo = 10 m/s cs 45° Qo= 0.10 cms FIGURE 6.15
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=6.1, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm 6 m/s 2 mis 60 cm Liquid
A Closed tank of water with Length, I = 20 ft Height, h = 10.45 ft %3D Width, w = 5.6 ft Pgage = 0 kPa at the top before acceleration is accelerating at an angle of 38° with respect to the horizontal, where the x component of the acceleration is parallel to that of the length of the tank at a rate of 6.35 ft/s² . If the tank is 76% %3D full, calculate the pressure at the bottom of the left side of the tank and the force acting at the top of the tank during acceleration. Take note that the tank is fixed such that it remains parallel to the horizontal during acceleration
A balloon is being filled with water at an instant when the diameter is 50 cm. If the flow rate into the balloon is 200gal/min, what is the rate of increase in the diameter?
An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per second. At the same time, receiving a fluid at a rate of 225 US Gal per minute. At a certain post the tank is considered to be quarter full. Find the (a) water level and the (b) mass change In the tank 15 minutes later. Given: tank diameter = 10 ft tank height = 20 ft
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=6.1, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm mis 2ns 60 cm Liquid