what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=6.1, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle.

what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=6.1, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the available suction head of a pump that is taking gasoline at 204 deg. C, from a closed tank with a pressure of 585 Kpa gage. The specific gravity of gasoline is 0.78 and its vapor pressure is 620 kpa absolute. The loss in the suction pipe is 0.5m and the pump centerline is located 3.60 meters above the gasoline level. answer is 4.47 how
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
Piston A has a cross-section of 1,200 cm^2 while that of piston B is 950 cm^2 with the latter higher than piston A by 1.75 m. If the intervening passages are filled with oil (s= 0.8), what is the difference in pressure between A and B?
Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
In order to measure the speed of the ambient air at atmospheric pressure, a Pitot tube is used, in which water is the gage fluid.. It is known that the ambient air speed is 25 meters per second, when the air temperature is 40 degrees. Celius. Calculate what the differential manometer reading in the pitot tube would be?
A pipe has an initial radius of r1, which then changes to a radius of r2. The velocity of the water in the initial part of the pipe is v1. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? let r1=10cm let r2=6cm let v1=5m/s b) What is the volume flow rate in the pipe?
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
It is required to pump water at 100 gal/min from a large reservoir to the surface of another reservoir 400 feet higher. What is the horsepower of the motor to drive the pump if the efficiency of the pump is 70%?
How long will it take the water surface in the tank shown to drop from h = 3 m to h = 50 cm?
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m