III. Calculations & Synthesis 1. Figure shows a big pancake of hot plastic put onto the cold bed of a mold. After cooling, the plastic will not remains flat and it will warp. Sketch the shape of the plastic after cooling and provides possible reasons that cause the warpage of the plastic. Hot plastic Cold bed

III. Calculations & Synthesis 1. Figure shows a big pancake of hot plastic put onto the cold bed of a mold. After cooling, the plastic will not remains flat and it will warp. Sketch the shape of the plastic after cooling and provides possible reasons that cause the warpage of the plastic. Hot plastic Cold bed

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

Ram a farmer, managed to grow shaped-watermelons inside glass cases ofdifferent shapes. The shapes he used were: a perfect cube, hemi-spherical, cuboid,cylindrical along with the normal spherical shaped watermelons. Thickness of the skinwas same for all the shapes. Each of the glass cases was so designed that the totalvolume and the weight of the all the water-melons would be equal irrespective of theshape. A customer wants to buy water-melon for making juice, for which the skin of the water-melon has to be peeled off, and therefore is a waste. Which shape should the customer buy?
A piece of lead (sp. Gr. 11.3) is tied to a 130 cc of cork whose specific gravity is 0.25. they float just submerged in water. What is the Buoyant force at cork?
In celebration of the end of term, see the symmetric wine glass of 300 g mass, as shown below.Note that the wine is frozen because you left the glass outside. What is the maximum force magnitude P that can be applied to the glass before movement occurs? What kind of movement will occur? What kind of movement will occur if the base is changed to be 120 mm wide, themass of the glass increases to become 400 g, and μs = 0.2?
A commpon way of salvaging cannons from old wreacks is to attach an inflatable balloon filed with air. Assume that the cannon is a solid cylinder of iron which is 1.30m long with a radius 17.3cm. The density of iron is 7.87g/cm^3. a. If an air bag were filled twice the volume necessary, what will be the tension in the rope between the air bag and the cannon when the air bag reaches the surface and comes to rest? What volume of air bag wil be floating above the water surface?
A piece of lead (sp. Gr. 11.3) is tied to a 130 cc of cork whose specific gravity is 0.25. They float just submerged in water. What is the weight of the cork?
A liquid is to be mixed at 400 rpm and the liquid height should be kept below 50 cm. If 100 L of liquid is to be mixed, what is the minimum and maximum radii of the container?
CONCEPTUAL QUESTION - Hydrostatic Forces in Layered Fluids How do you get the centroid of the inclined shape like in the picture? Like for F1 = PcgA1, you obviously need the centroid and the area, so how do you get it if it's inclined? Can anyone give an example?
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
In thermodynamic, a rigid tank may require you to deal with liqud or gas or both in the entire volume of the tank. Let’s say you need to create a container to keep one third of the volume inthe liquid phase in the form of steam water and the rest is in vapor, what are the parameters thatyou need to consider? Use relevant illustration of your design and prove it through yourcalculation.
On a square plank 10cm thick and weighing 10kg, a 50-kg man stands. What is the smallest possible dimension of the plank that would most likely result in sinking? What is the mass that will cause half of the plank to go submerged? COMPLETE SOLUTION PLEASE
Air, high cylinder volume 5 ft31.6 ft3 from / s/ s volume as if balancedcalculate the work required to compact. Initial starting and ordering temperature X psi and (X+ 20)Is ᵒF (X=10)
I'm looking forward to your solutionfluid mechanicsthanks