Illustrate the different components of Evacuated Tube System

Q: list down and explain four benefits of insulating a pipe conveying steam

A: given; list down and explain four benefits of insulating a pipe conveying steam

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: Which of the following device used to measure pressure difference in venturimeter? O a. Bourdon tube…

A:

Q: sketch and show the location of the pitot tube that is to be installed in an aeroplane

A: The purpose of the pitot tube in aircrafts is to measure the relative velocity of air streaming over…

Q: A report on the types of pressure devices

A:

Q: How long would it take to purge a 15ft section of 6in diameter pipe using a flow rate of 35cfh?

A: Given data length of the pipe L = 15ft  diameter of the pipe = 6in = 0.5ft Flow rate = 35cfh  To…

Q: Write short note on the Difference between the PVT diagram of water and other liquids

A: Solution: To Determine: The difference between the Phase diagrams of water and other liquid.

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: State two reasons copper pipe is becoming more popular for fire protection systems

A: Almost all fire protection systems use carbon steel, but the use of copper in fire protection…

Q: .eter

A:

Q: List the functions of a pneumatic valve

A:

Q: ____ commonly find applications in tires, O-rings, gaskets, seals, hoses for automobiles and trucks,…

A: ____________ commonly find applications in tires, O-rings, gaskets, seals, hoses for automobiles and…

Q: WHAT IS THE DIFFERENCE BETWEEN ROTARY AND AXIAL CPMPRESSORS

A: The axial compressor are used to increase the pressure of the gas. The gas is enters axially into…

Q: Explain about ball valve and also write the working pressure and temperature limit of ball valve.

A: A ball valve is the quarter turn valve which uses a hollow, perforated and pivoting ball to control…

Q: The pitot tube is used to measure the velocity of flow at the required point in a pipe Select one:…

A: The pitot tube is a velocity measuring device that is used to measure the velocity of the flow at…

Q: The cylindrical portion of short length, which connects converging and diverging section of…

A: Venturimeter - A venturimeter is a Flow measurement device used for measuring the flow rate of…

Q: A condenser vacuum gauge reads 705 mmHG when the barometer stands at 746 mmHG. State the absolute…

A:

Q: List some applications that use low-pressure piping

A: The low-pressure piping systems are used to carry nonhazardous materials that are used in Industry.…

Q: calculate heating surface of cylindrical tank

A: calculate the  heating surface of cylindrical tank

Q: How to  calculate the maximum stresses which are produced inside the boiler due to the pressure of…

A: How to  calculate the maximum stresses which are produced inside the boiler due to the pressure of…

Q: When the compressor and motor operate on the same shaft and are enclosed in a common casing is known…

A: This question is based on the concept of semi hermetic sealed compressor

Q: Describe the procedure for selection of expansion tank for a given hydronic piping system.

A: Given Expansion tank To find Selection procedure

Q: Give all the parts of a simple vertical fire tube boiler

A:

Q: Describe about Pressure compensated valve with construction and working in detail.

A: given; Describe about Pressure compensated valve with construction and working in detail.

Q: determine the number of fins required.

A: Given data, D=360×10-3mL=240×10-3mTb=550CLongitudenal fin;tfin=15×10-3mhfin=40×10-3h=40 w/m20 Ck=40…

Q: Determine the number of tubes that must contain of an HRT Boiler having a 60 inches diameter, 16 ft…

A: We have given

Q: Difference between overfeed and underfeed coal beds used in stem boilers

A:

Q: Enlist the names of places on aeroplane where the pitot-static tubes are located.

A: A pitot-static system is a setup comprising of pressure-sensitive instruments and is mostly used in…

Q: Discuss the difference between thin and thick walled pressure vessel

A: Difference between thin and thick walled pressure vessels Thin pressure vessel For thin pressure…

Q: hy there is a little amount of heat loss for fully covered insulated pipe compared to bare pipe?

A: To state the reason why there is a little amount of heat loss for fully covered insulated pipe…

Q: A piping system is made of 6-nominal schedule 40 cast iron. All fittings are threaded fittings (Clas…

A: The ASME B16.5 - 1996 Pipe Flanges and Flange Fittings standard covers pressure-temperature ratings,…

Q: The cylindrical portion of short length, which connects converging and diverging section of…

A: A venturi meter is a device that is used to measure the flow rate of fluid in a pipe. The venturi…

Q: 3. Drive an equation to describe the effect of the tube's diameter on the liquid raise in cupillary…

A:

Q: PA Prandtl tube (Pitot-static tube with C = 1) is %3D used to measure the velocity of water. The…

A: Calculated the velocity of water in (m/s).

Q: Describe the Various types of Bourdon tubes used to measure pressure. They work on the same…

A: Types of Bourdon tubes There are 3 main types of elastic elements for pressure measurement, namely…

Q: State the standard conditions for water to boil at 212°F.

A: In this problem, it is asking about the standard conditions for water to boil at 212°F.

Q: A square tube is welded on one side and will be filled with liquid of a relative density of

A: Liquid when enclosed within a container makes a pressure inside and then exerts force on the walls…

Q: Explain in detail, four types of pressures with relevant diagrams.

A: