A piping system is made of 6-nominal schedule 40 cast iron. All fittings are threaded fittings (Clas 125). Discuss whether or not this piping system is suitable for handling liquid water at room temperature and fluid pressure of 450 psi. | If ye provide supporting information. | If no, suggest the changes that could be made to the piping system.

A piping system is made of 6-nominal schedule 40 cast iron. All fittings are threaded fittings (Clas 125). Discuss whether or not this piping system is suitable for handling liquid water at room temperature and fluid pressure of 450 psi. | If ye provide supporting information. | If no, suggest the changes that could be made to the piping system.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.1P: Evaluate the Reynolds number for flow over a tube from the following data: D=6cm,U=1.0m/s,...

See similar textbooks

Similar questions

The Reynolds number is defined for a pipe as (velocity· diameter· density) / viscosity. What isthe Reynolds number for water flowing at 10 ft/ s in a pipe with a diameter of 6 in? What are itsdimensions?
Question - You must discuss in detail the way in which the pitot tube and nozzle flow meter are used to calculate velocity or volume flow rate. Write the velocity (or flow rate) equations for both and a detailed description of the what you did.
At approximately what volume flow rate will propyl alcohol at 77 °F become turbulent when flowing in a 3-in Type K copper tube?
The venturi meter is to be installed in a schedule 40 4-in(ID=4.026 in) line to measure the flow of water. The maximum flow rate is expected to be 325 gal/min at 60°F. The 50-in manometer used to measure the differential pressure is to be filled with mercury, and water is to fill the leads above the mercury surfaces. The water temperature is to be 60°F throughout. What throat diameter should be specified for the venturi meter?A. 2 inB. 1.5 inC. 1.0 inD. 0.5 in
Example 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is posted
## Industrial Piping Define a hypothetical piping system that interconnects equipment (consumers) and has at least two branches with diameters different from the diameter of the main branch. Express it, through a basic process flowchart, with a brief description of how it works. The system must contain Energy sources (reservoirs, tanks, compressors, pump, boiler...) and consumers (vessels, heat exchangers, tanks, machines...) Indicates the proper location for the installation of pressure relief valves, traps, drains, vents, and flow valves Indicate the TAGs of the equipment, valves, pipes and other installed devices Define the basic operating conditions (temperature, minimum and maximum operating pressure, fluid type) Define the basic physical conditions (material specification, pipe diameters Define the maximum design pressure, to be considered to be the MAOP (old and hot)
Evaluate the Reynolds number for flow over a tube from the following data: D=6cm,U=1.0m/s, =300kg/m3,=0.04Ns/m2.
A 6-nominal schedule 80 cast iron pipe is 3500 m long. It is to convey octane at a flow rate of 0.02 m3/s. Determinethe pressure drop of the octane.
1) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 2) The EGL is always a distance V2/2g above the HGL. True or False
In cases that there is a desired flowrate, what design considerations must be specified in the piping system if the mechanical energy losses are to be minimum? Explain briefly.
Calculate the fitting coefficient, , for the sudden expansion when fluid flows from a tube with a radius of 6 mm, to one with a radius of 24 mm. Assume the Reynolds number is 5,000 in the first tube. Enter your answer in decimal form, not scientific notation.
A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the allowable pressure drop is 0.006 lb force per s. in-ft pipe, what size of pipe is required