impedance coil takes 10 A and absorbs 250 W when connected across a 220 V, 60 Hz source. What power will it absorb when connected across 110 V, 25 Hz mains?

Q: 40. A polarity test is performed upon a 1,150/i15-volt transformer. If the input voltage is 116,…

A:

Q: . A 5 HP, 3-phase induction motor draws a current when connected to 230-V. Determine the current…

A:

Q: A small filament transformer has a laminated sheet steel core whose average path length is 20cm and…

A: Given Average path lenght = 20 cm Cross sectional area = 5 cm2 Primary winding connection 120 V and…

Q: What's the maximum primary overcurrent device rating for a 0.50 kVA (500 VA), single-phase, 240V…

A: single phase transformer: S=VpIp500=240IpIp≅2.08 Ampere

Q: A voltage transformer has 1500 turns of wire on its primary coil and 500 turns of wire for its…

A:

Q: The primary winding of a transformer connected to 2,200 volts circuit consists of two coils which…

A:

Q: A current transformer with bar primary has 300 turns in its secondary winding. The resistance and…

A: A bar type current transformer utilizes the real cable or bus-bar of the main transformer as the…

Q: A single phase motor is rated 5hp, 75% pf lag,220V. What is the approximate size of capacitor is…

A: It is given that:P=5HPP=5×746P=3.730 kWV=220 Vpower factor,cosϕ1=75%cosϕ1=0.75Required power…

Q: A current transformer is described as 10VA 10P20, 1500/5. Determine: (i) (c) whether it is a…

A: Basic Equipment used in High voltage transmission Circuit Breaker Lightning Arrester Measuring…

Q: what do you call an equipment that changes the voltage higher or lower without changing the…

A: =>  Capacitor  bank :- It is used to improve the power factor of the system.  =>  Switchgear…

Q: Which one of the following is damaging to many insulating materials used in alternators? A. Eddy…

A: According to the question we have to discuss which one of the given damaging to many insulating…

Q: 1) A 0.0159 HInductance coil and a 40 ohm resistor are connected in series across 240 volts, 60…

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: Question five: A single phase, 10 kVA, 2400/120 V, 60 Hz transformer has the following equivalent…

A: Single phase transformer 2400/240V , 10kVA, 60Hz Short circuit impedance and open circuit parameters…

Q: A transformer has a primary voltage rating of 240 V and a secondary voltage rating of 80 V. If the…

A: The given transformer is a step-down transformer. It is connected in the subtractive polarity. In…

Q: A single-phase 230V, 1kW heater is connected across I-phase 230V, 50Hz supply through an SCR. For…

A:

Q: The input impedance of an impedance transformer after inclusion in the circuit is 70Ω. What is the…

A:

Q: A 3-phase, induction motor has the following no-load test data: No load (per phase):  120 V, 5 A,…

A: In this question, We need to determine the magnetizing reactance per phase of the approximate…

Q: single-phase transformer has 200 turns on the primary and 36 turns on the secondary.  If the primary…

A:

Q: . A 480/120 V, 5kVA two winding transformer is to be used as an autotransformer to supply power at…

A:

Q: Q4/ The equivalent circuit impedances of a 20-kVA, 8000/240 V, 60-Hz transformer are to be…

A: I am attaching detailed  solution image of this question.

Q: AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with…

A:

Q: How do i calculate secondary current in transformer analysis

A: Given that  calculate secondary current in transformer analysis

Q: In a 400 V, 50 c/s transformer, the total iron loss is 2500 W. When the supplied p.d. is 220 V at 25…

A:

Q: The high-voltage side of a transformer has 750turns, and the low-voltage side has 50 turns. When…

A: Given data: N1=750N2=50V1=120 VI2=40 A a) The expression for the turns ratio is given as,…

Q: A transformer has a 240 V primary and a 120 V secondary. With a 12 ohm load connected, what is the…

A: Drawing the circuit diagram for the given condition:

Q: mode of operation: e and rms value of load current e and rms value of thyristor current

A: The RMS load current per phase is given by:…

Q: Determine the Current Density for the following transformer winding (Fill Factor = acceptable? 0.92)…

A:

Q: What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer?…

A: The relationship between primary induced emf( E1) and applied voltage (V1)

Q: A 1-phase transformer converts 120V to 208V.  It is rated for 3 kVA.  What is the lowest resistance…

A:

Q: The high-tension winding of a 100-KVA; 2,300/575 volts, 60-cycle transformer consists of 200 turns…

A: The transformer is a static device that helps to step up or down the voltage or current level by…

Q: Draw a block diagram of a power supply from transformer up to regulator with corresponding waveform.

A: The block diagram of Regulated power supply is shown below. The basic building blocks of a…

Q: In 3-phase induction motor control over load relay can be connected anywhere in the circuit. Select…

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: 6.) . The NTD fuse rating for a 230 V, 3Ø, 50 hp synchronous motor with an 80 % power factor using…

A:

Q: The winding of a 4-pole alternator having 36 slots and coils and a coil span of 1 to 8. What is the…

A: The solution is given below

Q: Safety considerations require that the CT has to be short circuited (or the primary circuit switched…

A: Current transformers are useful to measure higher ac currents. This is due to the unavailability of…

Q: if the transformers is supplied with 500 volts to the primary coil with a 200 turns; and 15,000…

A: In this question,   We need to determine the the voltage on the secondary ?

Q: When 120 V, 60 Hz is applied to the primary winding of a transformer, the core loss is 240 W. When…

A:

Q: When 120 V, 60 Hz is applied to the primary winding of a transformer, the core loss is 240 W. When…

A:

Q: A one-phase transformer has 400 and 1000 turns in primary and secondary, respectively. The…

A: Given, a one-phase transformer having Primary turns, N1=400  Secondary turns, N2= 1000 Primary…

Q: For a 50 kVa distribution transformer, which on its high voltage side is 2400 V and on the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: A polarity test is performed upon 1150/115-volt transformer. If the input voltage is 120 V,…

A:

Q: 8. A 10 HP, 6 pole, 60 Hz, 3-phase SCRIM delivers 9.9 HP, with an input of 9200 W. The core loss is…

A:

Q: Q.5. When a transformer is connected to the supply, how its windings are named? Q.f tanaular.coils…

A:

Q: 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the KVA rating of…

A: Given data: KVA Rating, S=900 kVAInitial Power factor cos ϕ1=0.707ϕ1=cos-10.707=450

Q: A Transformer having 1200 Primary turns connected to a 264 V a.c. supply. For a secondary Voltage of…

A:

Q: An impedance coil takes 10 A and absorbs 250 Watts when connected across a 220 V, 60 Hz source. What…

A: This question belongs to circuit theory . It is based on the concept of power consumed across the…

Q: The no-load current of a transformer is 5.0 A at 0.3 power factor when supplied at 230-V, 50-Hz. The…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: 24,000/2400-v single- phase transformer at 40 per turn. find the number of turns on each winding and…

A: To determine the number of turns on both winding in a transformer. Given: Rating = 1000 KVA,…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.