In a 35,000-kW turbogenerator that receives steam at 6.9 MPa and 370°C, 11% of the throttle steam is actually extracted at 2 MPa, 215°C; with the remainder being re heated to 1.8 MPa and 315°C; then 20% of the throttle steam is actually extracted at0.724 MPa, each extraction serving an open feedwater heater. The engine exhaust to a condenser pressure of 0.005 MPa and the temperature of the feedwater from the last heater is 205°C. The combined steam rate of the turbogenerator unit is 4.898 kg/kwh and the generator efficiency is 95%. For the total throttle flow to an ideal engine, find (a) extracted steam for the last heater, (b) W, (c) e. For the actual engine, find (d) e, (e) n. (f) What is the enthalpy of the actual exhaust when the pump efficiency is 60%?

In a 35,000-kW turbogenerator that receives steam at 6.9 MPa and 370°C, 11% of the throttle steam is actually extracted at 2 MPa, 215°C; with the remainder being re heated to 1.8 MPa and 315°C; then 20% of the throttle steam is actually extracted at0.724 MPa, each extraction serving an open feedwater heater. The engine exhaust to a condenser pressure of 0.005 MPa and the temperature of the feedwater from the last heater is 205°C. The combined steam rate of the turbogenerator unit is 4.898 kg/kwh and the generator efficiency is 95%. For the total throttle flow to an ideal engine, find (a) extracted steam for the last heater, (b) W, (c) e. For the actual engine, find (d) e, (e) n. (f) What is the enthalpy of the actual exhaust when the pump efficiency is 60%?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam at 10 MPa, 600C enters the first-stage turbine of an ideal Rankine cycle with reheat. The steam leaving the reheat section of the steam generator is at 500C, and the condenser pressure is 6 kPa. If the quality at the exit of the second stage turbine is 90%, determine the cycle thermal efficiency.
A 60 MW power plant operates with a reheat cycle. The steam enters the turbine at 15 MPa, 590°C. The steam enters the reheater at 1.95 MPa and 280°C and exits at 1.8 MPa, 590°C. Conden pressure is. 0.0035 MPa. The steam rate is 150.000 kg/hr, and the generator efficiency is 90%. Determine the following: 1. Ideal cycle thermal efficiency without pressure drop 2. Actual cycle thermal efficiency 3. Actual combined engine efficiency 4. Enthalpy of exhaust steam (at point 4) if the heat lost through the turbine casing is 2% of the combined work.
Compare the thermal efficiency and turbine-exit quality (temperature if superheated) at the condenser pressure for a simple Rankine cycle and the reheat cycle when the boiler pressure is 5 MPa, the boiler exit temperature is 500°C, and the condenser pressure is 20 kPa. The reheat takes place at 0.5 MPa and the steam leaves the reheater at 500°C. (Enthalpies are in KJ/kg.) Without the reheater, the enthalpy at the turbine exhaust is: Without the reheater, the quality at the turbine exhaust is: The pump work is: The enthalpy leaving the reheater is: The thermal efficiency is:
1. A reheat cycle with two stages of reheating is executed with steamexpanding initially from 90 bar and 530°C. The two reheaterpressures are 10 bar and 0.6 bar, and the steam leaves eachreheater at 480°C.Condensation occurs at 0.03 bar. Find the cycleefficiency.2. An ideal reheat turbine with one stage of reheat receives steam at8.0 MPa and 480°C. Reheat pressure is 0.83 MPa and exhaustpressure is 0.007MPa. The work is 1559 KJ/kg and thermalefficiency is 41%. Find the temperature of the steam leaving thereheater.
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency
Compare the thermal efficiency and turbine-exit quality (temperature if superheated) at the condenser pressure for a simple Rankine cycle and the reheat cycle when the boiler pressure is 5 MPa, the boiler exit temperature is 500°C, and the condenser pressure is 20 kPa. The reheat takes place at 0.5 MPa and the steam leaves the reheater at 500°C. (Enthalpies are in KJ/kg.) Without the reheater, the thermal efficiency is: The temperature at the exhaust of the low-pressure turbine is: The throttle enthalpy is: The heat added in the boiler is: The enthalpy at the suction of the pump is:
An air-standard Brayton cycle has an air leaving the high-temperature heat exchanger at 850 degree C and leaving the turbine at 310 degree C . What is the thermal efficiency?
3. A 200 MW power plant operates on a simple Rankine cycle. Steam at 5.2 MPa, 400ºC expandsin a Rankine turbine to 0.036 MPa. Assume actual turbine with isentropic efficiency of 75 % forboth the compressor and expander. 3.1 Heat added in steam Generator , KW 3.2 Power loss at Turbine, KW 3.3 Actual thermal efficiency of the cycle 3.4 Mass of water in kilogram needed for an hour in the condenser if the changeof temperature for the water is 27ºF
In a reheat cycle steam at 15 MPa, 540°C enters the engine and expands to 1.95 MPa. At this point the steam is withdrawn and passed through a reheater. It reenters the engineat 540°C. Expansion now occurs to the condenser pressure of 0.0035 MPa. (a) A 60,000 kw turbine operates between the same state points except that the steam enters the reheater at 1.95 MPa and 260°C, departs at 1.8 MPa and 540°C. The steam flow is 147,000 kg/hr, generator efficiency is 96%. For actual engine, find, ek, mk, and nk, (b) Determine the approximate enthalpy of the exhaust steam if the heat lost through the turbine casing is 2% of the combined work.
In a reheat cycle steam at 15 MPa, 540 ̊C enters the engine and expands to 1.95 MPa.At this point the steam is withdrawn and passed through a reheater. It reenters the engineat 540 ̊C. Expansion now occurs to the condenser pressure of 0.0035 MPa (a) For theideal cycle, find e. (b) A 60,000 kw turbine operates between the same state piontsexcept that the steam enters the reheater at 1.95 MPa and 260 ̊C, departs at 1.8 MPa and540 ̊C. the steam flow is 147,000 kg/hr, generator efficiency is 96%. For actual enginefind ek, mk, and nk.
rankine cycle, the pressure and temperature entering the turbine is 1800 kpa and 380 degrees celsius and the pressure leaving the turbine is 20 kpa, the quality of steam entering the condenser is 90%. what is the turbine work in kj/kg at 1.8 mpa and 380 degrees celsius
A 8000 kW gas-turbine power plant operates with single stage compression, two-stageexpansion and with a reheating process. The high pressure turbine drives the compressor andthe low pressure turbine produces the net work output. Atmospheric air enters the compressorat 27 oC and the combustion gasses enter the high pressure turbine at 927oC. The combustiongasses leaving the high pressure turbine is reheated back to 827 oC before expanding in the lowpressure turbine. The overall pressure ratio is 9. The isentropic efficiency of each turbine is85% and the isentropic efficiency of the compressor is 90%. Sketch the schematic diagram andthe temperature-entropy (T-s) diagram of the cycle. Determinei. the heat supplied to the system, kJ/kgii. the net work, kJ/kgiii. the thermal efficiency, %iv. the work ratiov. the mass flow rate of the gasses, kg/s.For air take cpa = 1.005 kJ/kgK and a = 1.4 and for the gasses takecpg = 1.15 kJ/kgK and g = 1.33