Answered: In a machining operation, doubling the…

In a machining operation, doubling the cutting speed reduces the tool life to 1/8th of the original value. What is the exponent n in Taylor's tool life equatio

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.4: Saws And Cutoff Machines

Problem 2RQ: The vertical band saw is particularly useful, as it can be used to make straight cuts as well as...

See similar textbooks

Related questions

Q: (b) During a certain machining experiment at the UCSI workshop, it is observed that temperature at…

A: (i). In a metal cutting process, Maximum heat is carried out by chip then tool and lastly by the…

Q: The rpm (N) of the shaft, diameter (d) =25 mm, cutting speed (v) =50 m/min is; O 39.25 O 636.9 O…

A: Given data as per question Diameter of shaft=25 mmcutting speed =50mmincalculating speed of…

Q: Turning tests have resulted in 1 min tool life at a cutting speed = 4.0 m/s and a 20 min tool life…

Q: A workpiece from AISI 1020 steel will be produced by machining on a lathe. The recommended cutting…

A: Machining is a material removal process in which unwanted material is removed in the form of chips…

Q: .48 Let n = 0.5 and C = 400 in the Taylor equation for tool wear. W hat is the percent increase in…

A: Given Data: The value of n=0.5. The value of C=400. Taylor equation for tool wear can be expressed…

Q: Q3 Provided below is the Tool life data for cutting low carbon steel with HSS tool . Draw the tool…

A: The tool life equation in linear form can be expressed as,

Q: Turning tests were performed using a coated carbide tool on steel workpiece at feed of 0.30 mm/rev…

Q: During turning tests, using a cemented carbide tool resulted in a 1‑min tool life at a cutting speed…

Q: The following data was obtained from an orthogonal cutting test: Rake angle = 20° Chip length before…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: In orthogonal machining operation the chip thickness and the uncut chip thickness are equal to 0.45…

A: Given:Chip thickness=uncut chip thickness=0.45 mmt1=t2=0.45 mmr=1α=0o

Q: Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm…

A: Given data: - The initial diameter of the rod is D = 65 mm. The final diameter of the rod is d = 58…

Q: regrind and machining cost is Rs.10/min. Tool change time is 2 min. Optimum cutting speed (in m/min)…

Q: length is 1100 mm. The feed is 0.35 mm/rev and the depth of cut is 2.5 mm. The cut will be made with…

A: Given data:-diameter of bar, D=400mmLength of bar, L=1100mmfeed, f=0.35mm/revdepth of cut,…

Q: During orthogonal cutting of MS with a 10 ° rake angle tool, the chip thickness ratio was obtained…

A: Given data: The rake angle is θ = 10o. The chip thickness ratio is r = 0.4.

Q: . Let n = 0.5 and C = 90 in the Taylor equation for tool wear. What is the percent increase in…

A: GIVEN DATA- IN TAYLOR TOOL LIFE EQUATION n=0.5, C=90

Q: Calculate the machining time to complete the job as shown below from a bar 120 mm long and 60 mm…

A: Given: length of the job→L=120 mm initial diameter→D=60 mm maximum depth of cut→d=5 mm hence in…

Q: he outside diameter of a cylinder made of steel is to be turned. The starting diameter is 120 mm and…

A: From the given data,

Q: *Using the Taylor equation for tool life and Tetting n = 0.5 and C= 400, calculate the percentage…

A: Given that, Tool exponent, n=0.5,Constant, C=400,Cutting speed is reduced by 50 %, Writing Taylor…

Q: value. The exponent nin Taylor's tool life equation In a machining operation, doubling the cutting…

Q: In a cutting test with 0.3 mm flank wear as tool failure criterion, a tool life of 10 min was…

Q: In machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value.…

Q: The tool life equation for HSS tool is VT0.14f 0.7d 0.4 = Constant. The tool life (T) of 20 min is…

A: Given data: The initial tool life is T = 20 min. The initial velocity is V = 40 m/min. The initial…

Q: In a cutting test with 0.3 mm flank wear as tool failure criterion, a tool life of 10 min was…

A: Taylor's tool life equation is given by F.W. Taylor. Taylor's tool life equation gives the relation…

Q: 3. Using a lathe machine having a motor power of 4 KW and mechanical efficiency of 0.85, calculate…

A: Given: The power of the motor is, P=4 kW. The mechanical efficiency of the motor is, η=0.85. The…

Q: Example 4.2.5: Turning tool made of HSS used in the long process of turning shaft of aluminum alloy…

Q: In a turning operation, the tool life varies with cutting speed, as shown in following table:…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

Q: n machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value.…

A: Given; Taylor tool life equation is given as : VTn=CV= velocityT = tool life n is the Taylor tool…

Q: Give 3 reasons why conventional machining is essential. b. What is the difference between the…

A: (A) Machining refers to the process in which a cutting tool is used to cutting material from the…

Q: A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a…

A: Proper tool Nose radiusing improves machinability to some extent though. It increase the tool life…

Q: A tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10…

A: Given:initial rake angle, α1=10ofinal rake angle, α2=7o

Q: (j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min,…

A: Given data : stainless steel with hardness = 200 HB cutting speed (v) = 250 m/min feed (f) = 0.3…

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

Q: In an orthogonal cutting test, the cutting force and thrust force were observed to be 1000N and 500…

A: Given data: The cutting force is FC = 1000 N. The thrust force is FT = 500 N. The rake angle is θ =…

Q: To what factors do you attribute the difference in the specific energies in machining the materials…

A: Solution:

Q: You are trying to determine the proper cutting conditions for a metal component There are twe…

A: given data;axial lenth of cut (Le)=50mmdiameter(d)=15mmfeed(f)=0.1mm/revproduction rate requirments…

Q: 2 1.54 Explain how you would go about estimating the C and n values for the four tool materials…

A: Generally n depends on tool material and C on work piece material,VTn=CForm the given graph , the…

Q: 1. In a production turning operation, the cylindrical workpiece is 425 mm long and 190 mm in…

Q: 5. As you know, there is a wide range of tool materials available and used successfully today, yet…

Q: Explain whether it is desirable to have a high or low (a) n value and (b) C value in the Taylor…

Q: 2 1.63 With a carbide tool, the temperature in a cutting operation is measured as 650K when the…

A: Given: feed = 0.05 mm/rev T1=650 K

Q: Example 4.2.4: In testing operation for two cutting tools from the same material, found that first…

A: Given data:

Q: d) Use the Taylor Tool Life equation to estimate the tool life (in minutes) for this operation. Use…

A: Every gadget or tool has a limited lifespan. It may continue to function after that time has passed,…

Q: The Taylor tool-life equation is directly applicable to flank wear. Explain whether or not it can be…

A: Solution:

Concept explainers

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.

Question

In a machining operation, doubling the cutting speed reduces the tool life to 1/8th of the original value.

What is the exponent n in Taylor's tool life equation VTⁿ = C,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a turning operation, the tool life varies with cutting speed, as shown in following table:Cutting speed, V, m/min Tool life, T, min25 3070 2 Estimate the tool life for this operation at a speed of 60 m/min.
2 1.23 Tool life can be almost infinite at low cutting speeds.Would you then recommend that all machining be done at low speeds? Explain.
Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Assume that, in orthogonal cutting, the rake angle, oz,is 20° and the friction angle, B, is 35° at the chip-tool interface.Determine the percentage change in chip thickness when the friction angle is 50°. (Note: do not use Eq. (21.3)
A tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10 to 7 deg, Calculate the approximate % change in the life of the tool.
In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour and 40 minutes, at a spindle speed of 25 m/min. Calculate the tool life if it has to be operated at a speed of 30% higher than the initial cutting speed. Also calculate the cutting speed if the tool is required to have a life of 2 hours and 45 minutes. Assume Taylor’s exponent value n is 0.28.
In machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value. What is the Taylor's tool life index (n) for a machining operation?
what are the three basic parameters (cutting variables) in the machining process? how to calculate them
2 2 . 16 Explain why so many different types of cutting-tool materials have been developed over the years. Why are they still being developed further?
In a machine test, a cutting speed of 100 m/min indicated the tool life as 16 min and a cutting speed of 200 m/min indicated the tool life as 4 min. Calculate the values of n and C.
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the cutting velocity is 90 m/min The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm If the orthogonal rake angle is zero and the principal cutting edge angle is 90° Calculate the shear angle in degree.
Since the cutting plane angle is 9.5°, the cutting depth is 0.4 mm, the chip thickness is 2.9 mm, the cutting width is 3.1 mm, and the shear strength is 185 MPa in the orthogonal cutting process; a) Find the rake angle (α).b) Find the shear deformation (γ).c) Find the shear force. (Note: The shear force is 1.4 times the thrust.)