In a motor-generator set, calculate the number of poles required in the motor to convert AC 60 Hz input, to AC 50 Hz output. Given that the number of poles of the generator is given as 10 poles. Select one: O a. Pm = 18 poles O b. Pm = 12 poles O c. Pm = 8 poles O d. None O e. Pm = 10 poles Clear my choice

In a motor-generator set, calculate the number of poles required in the motor to convert AC 60 Hz input, to AC 50 Hz output. Given that the number of poles of the generator is given as 10 poles. Select one: O a. Pm = 18 poles O b. Pm = 12 poles O c. Pm = 8 poles O d. None O e. Pm = 10 poles Clear my choice

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter39: Synchronous Motor Operation

Section: Chapter Questions

Problem 14SQ: Induction motors and welding transformers require magnetizing current, which causes a. lagging power...

See similar textbooks

Similar questions

Induction motors and welding transformers require magnetizing current, which causes a. lagging power factor. b. leading power factor. c. unity power factor. d. zero power factor.
A lap connected 6 pole DC generator has an armature conductors of 500 and is driven at 600 rpm. If the flux per pole is 15 mWb, then the generated e.m.f is, Choose correct answer : A) 75 V B) 100 V C) 250 V D) 225 V
If Radj can be adjusted as shown, what is the maximum no-load terminal voltage of this generator in volts? What is the setting of Radj in ohms if the generator is operating at its rated conditions (Output power Pout = 10 kW & Terminal voltage VT= 100 V)? (Answer in 2 decimal places)
plz help! A dc generator is rated at 19 kWkW , 250 VV, and 76 AA when it rotates at 1200 rpmrpm . The resistance of the armature windings is 0.34 ΩΩ . Q1:Calculate the "no-load" voltage at 1200 rpmrpm (when there is no circuit hooked up to the generator). Q2:Calculate the full-load voltage (i.e. at 76 AA ) when the generator is run at 780 rpmrpm . Assume that the magnitude of the magnetic field remains constant.
ASAP a.) In a separately excited dc generator, if the current in the field winding increases, the terminal voltage of the machine _______. b.) If the value of the field flux in a dc generator increases, the generated emf will ________. choices: increase, decrease, the same, zero
A 20-pole, Y-connected, three-phase, 400-Hz alternator has 3 coils per phase group. Each coil has 2 turns and the flux per pole is 23 mWb. The coils are connected in two parallel groups. Determine (a) the rotor speed, (b) the number of slots in the armature, (c) the winding factor, (d) the per-phase voltage, and (e) the line voltage.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES Answer the following questions (A, B and C) depending on the topic. 1. ALTERNATORS A. Why is it necessary to maintain the speed of an alternator at all times and how do they control the speed of an alternator when in operation? B. Distinguish between half-coiled and full-coiled armature windings in alternators. C. Why are fractional pitch windings generally used in alternators?
A lap connected 6 pole DC generator has an armature conductors of 500 and is driven at 600 rpm. If the flux per pole is 15 mWb, then the generated e.m.f is,؟ 250 V 225 V 75 V 100 V
A separately-excited DC generator with magnetization curve shown below (Figure 1) is driven by a prime mover at 1500 rpm. The armature resistance is 0.1 ohms. What is the internal generated voltage of this generator if VF = 15 Vdc and RF = 2.44 Ω if this generator is connected to a 100 ohm resistor load, what is the load current in amperes? Note that the armature has a resistance and will be in series with the load.
The result of no-load test on a 3-phase Y-connected induction motor are as follows: line to line voltage =400v; input power= 1770W; input current =18.5A; friction and windage loss = 600W. Determine:1. resistance per phase representing the core loss2. the magnetizing reactance per phase of the core.
(3) A four - pole DC long shunt compound generator with a wave wound armature, having 390 conductors, has to supply a load of 500 lamps each of 100 W at a terminal voltage of 250 V. The flux per pole is 30 mWb. The generator has, Ra = 0-05 22. Rs = 0-01 Q and Rf = 100 2. The iron and rotational losses are 1000 W and 1750 W respectively. a) Determine the total power of the load. b) If half of the lamps are tumed OFF. calculate the required generated voltage, Eg. and the speed of the generator. c) Determine the input power to the generator, when all lights are ON. d) Calculate the efficiency of the generator, when all lights are ON.
1. i)What are the different ways to supply DC power to rotor of an alternator? Which method is superior and why? ii)How do you define ‘static stability limit’ of an alternator?