In a once-through boiler, feed water enters through the bottom of tubes,receives heat from combustion of coal, and escapes from the top of thetubes as superheated steam, calculate the heat transfer coefficients ofwater and superheated steam using the following data:Pressure of feed water at tube inlet = 22.0 MPaAbsolute temperature of feed water, Tf =523 KPressure of superheated steam at tube outlet = 22.5 MPa%3DAbsolute Temperature of superheated steam, Tg = 868 KVelocity of Feed water through each tube. Vf = 8 m/sInternal diameter of each tube = 53.5 mm%3DLength of pipe = 120mUse, Density of water = 818.25 kg/m3Density of steam = 63.34 kg/m3%3D

Given data-pressure of feed water at turbine=22.0 MpaTf=523KSuper heated steem pressure…

In a once-through boiler, feed water enters through the bottom of tubes, receives heat from combustion of coal, and escapes from the top of the tubes as superheated steam, calculate the heat transfer coefficients of water and superheated steam using the following data: Pressure of feed water at tube inlet = 22.0 MPa %3D Absolute temperature of feed water, Tf =523 K Pressure of superheated steam at tube outlet = 22.5 MPa Absolute Temperature of superheated steam, Tg = 868 K

In a once-through boiler, feed water enters through the bottom of tubes, receives heat from combustion of coal, and escapes from the top of the tubes as superheated steam, calculate the heat transfer coefficients of water and superheated steam using the following data: Pressure of feed water at tube inlet = 22.0 MPa %3D Absolute temperature of feed water, Tf =523 K Pressure of superheated steam at tube outlet = 22.5 MPa Absolute Temperature of superheated steam, Tg = 868 K

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 16RQ: Explain why a waterless, earth-coupled, closed-loop geo-thermal heat pump system is more efficient...

See similar textbooks

Similar questions

Explain why a waterless, earth-coupled, closed-loop geo-thermal heat pump system is more efficient than a conventional closed-loop geothermal heat pump system.
In a once-through boiler, feedwater enters through the bottom og tubes, receives heat from combustion of coal, and escapes from the top of the tubes as superheated steam, calculate the heat transfer coefficients of water and superheated steam using the following data: Pressure of feedwater at tube inlet = 27.0 MPa Absolute temperature of feedwater, Tf =563 K Pressure of superheated steam at tube outlet = 24.5 MPa Absolute Temperature of superheated steam, Tg = 838 K Velocity of Feedwater through each tube. Vf = 6 m/s internal diameter of each tube = 63.5 mm Length of pipe = 30m
A jacketted-agitated vessel, fitted with a turbine agitator, is used for heating a water stream from 10°C to 54°C. The average heat transfer coefficient for water at the vessel’s inner-wall can be estimated from Nu = 0.76Re2/3Pr1/3. Saturated steam at 100°C condenses in the jacket, for which the average heat transfer coefficient in kW/m2·K is ho=5 13.1(Tg - Tw)20.25. The vessel dimensions are Dt = 0.6 m, H = 0.6 m and Da = 0.2 m. The agitator speed is 60 rpm. Calculate the mass rate of water that can be heated in this agitated vessel steadily.
The condenser of a room air conditioner is designed to reject heat at a rate of 15,000 kJ/h from refrigerant-134a as the refrigerant is condensed at a temperature of 40°C. Air (cp = 1005 J/kg·K) flows across the finned condenser coils, entering at 25°C and leaving at 35°C. If the overall heat transfer coefficient based on the refrigerant side is 150 W/ m2·K, determine the heat transfer area on the refrigerant side.
Consider a gas turbine of 200 kJ/kg net work, operating under standard cold air assumptions. Determine the thermal efficiency, in %, of the turbine, if it has a regenerator with 90% efficiency.
750 kg of dry saturated steam at a pressure of 160 N/cm2 is generated in a boiler per hour. The temperature of feed water is 28°C and the steam from the boiler enters the super heater after a heat loss of 690 kJ/kg, where it is superheated such that the degree of superheat is 250°C. Determine i) Dryness fraction of the steam at the entry point of the super heater ii) Heat absorbed per hour in the super heater iii) Total heat supplied to the inlet water in the boiler
Ethanol is vaporized at 788C (hfg 5 846 kJ/kg) in adouble-pipe parallel-flow heat exchanger at a rate of 0.03 kg/sby hot oil (cp 5 2200 J/kg?K) that enters at 1208C. If the heattransfer surface area and the overall heat transfer coefficientsare 6.2 m2and 320 W/m2?K, respectively, determine the outlettemperature and the mass flow rate of oil using (a) the LMTDmethod and (b) the e2NTU method.
What is application of parallel flow heat exchanger? and counter flow heat exchanger?
In general, heat exchangers with higher flow rates have greater capacities?
Air (Cp = 1005 J/kg °C) enters a cross-flow heat exchanger at 10 C at a rate of 3 kg/s, where it is heated by a hot water stream (Cp = 4190 J/kg °C) that enters the heat exchanger at 95 °C at a rate of 1 kg/s. Determine the maximum heat transfer rate and the outlet temperatures of the cold and the hot water streams for that case.
In large steam power plants, the feedwater is often heated in closed feedwater heaters, which are basically heat exchangers, by steam extracted from the turbine at some stage. Steam enters the feedwater heater at 1.6 MPa and 250°C and leaves as saturated liquid at the same pressure. Feedwater enters the heater at 4 MPa and 30°C and leaves 10°C below the exit temperature of the steam. Neglecting any heat losses from the outer surfaces of the heater, determine the ratio of the mass flow rates of the extracted steam and the feedwater heater.
a power plant steam, steam is continuously extractedfromthe turbine and in a heat exchanger there is a condensation of the extracted steam. The energy released during condensation of steam is used to operate a heat engine. A heat engine receives thermal energy at a rate of 1200 kJ/hr from condensing steam and rejects waste heat to a lake at 20°C at a rate of 800 kJ/hr. Determine the lowest possible condensing steam temperature.