Problem 8-12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is bent in the shape of a horse shoe having a mean radius of 70 mm. Two equal and opposite forces of 10 kN each are applied at a distance of 12 cm from the centre line of the middle section so that they tend to straighten the rod. Find the maximum ten- sile and compressive stresses and construct a diagram showing the vari- ation of the normal stresses over the central section.

Problem 8-12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is bent in the shape of a horse shoe having a mean radius of 70 mm. Two equal and opposite forces of 10 kN each are applied at a distance of 12 cm from the centre line of the middle section so that they tend to straighten the rod. Find the maximum ten- sile and compressive stresses and construct a diagram showing the vari- ation of the normal stresses over the central section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
A bar of rectangular section shown in is subjected to stresses σx, σy and σz in x, y and z directions respectively. Show that if sum of these stresses is zero, there is no change in volume of the bar.
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 1% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoop) stress is.....
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
Find the safe value of the axial load P in a circular column consists of circular 125mm wooden post and a 200mm x 200mm concrete footing separated by a steel plate. The working stresses are 15 MPa for wood and 18 MPa for concrete.
A thin-walled cylindrical vessel has an internal diameter of 1 m and a thickness of 10 mm subjected to an internal pressure of 2 bar. The vessel surrounded by two semicircular rings tightens by two bolts as shown in the figure below. knowing that the diameter of the bolt is 12 mm and the length of the vessel is 4 m, determine the tensile stress induced in the bolt.
A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
A bar AB of length L and uniform cross section is attached to rigid supports at A and B before being loaded. What are the stresses in portions AC and BCdue to the application of a load P at point C
A 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of 10 mm. If each side of the triangle is 200 mm measured at the median line and the allowable torsional stress is 40 MPa, what is the angle of twist in radians? (Use G = 70 GPa)
A prismatic bar with a length L = 3ft and cross- sectional area A= 8in2 is compressed by an axial centroidal load P= 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W=35", and show the stresses on a properly oriented stress element.