Water at 20 °C flows through a horizontal 1-mm-diameter tube to which are attached two pressure taps a distance 1 m apart. (a) What is the maximum pressure drop allowed if the flow is to be laminar? (b) Assume the manufacturing tolerance on the tube diameter is D = 1.0 0.1 mm. Given this uncertainty in the tube diameter, what is the maximum pressure drop allowed if it must be assured that the flow is laminar? 5.

Water at 20 °C flows through a horizontal 1-mm-diameter tube to which are attached two pressure taps a distance 1 m apart. (a) What is the maximum pressure drop allowed if the flow is to be laminar? (b) Assume the manufacturing tolerance on the tube diameter is D = 1.0 0.1 mm. Given this uncertainty in the tube diameter, what is the maximum pressure drop allowed if it must be assured that the flow is laminar? 5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
Air at 15°C flows through a large duct and thence through a 75-mm-diameter hole in the thin metal (c= 0.62). A U-tube gage containing water registers 31.7 mm. Considering the specific weight of air constant, what is the flow through the opening? KINDLY INCLUDE FBD AND ANSWER MUST BE = 46 N/min
Consider flow of blood in the microvessels of the body, assuming Poiseuille’s law holds and that the viscosity of the blood is constant. Consider a parent vessel that bifurcates into two daughter segments, all within the microcirculation and with blood flow described using Poiseuille’s law (assume that each segment has a different diameter and length).Denoting the pressure at node i by pi (i=1,2,3,4), and the flux in segment j by Qj (j=1,2,3), write down expressions for the segment fluxes in the network, in terms of the nodal pressures. How are the three volume fluxes related, and why? Assuming that the pressures at nodes 1, 3, 4 (the boundary nodes) are known, write down an expression for the pressure at the interior node, p2.
liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a pipe of diameter 12.5mm with a surface roughness equivalent to that for structural steel. What is the magnitude of the pressure gradient necessary to achieve this flow? Your answer should have a positive sign and be to the nearest 10 Pa/m. You may wish to use the Moody diagram.
Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a diameter of 35 mm. If the acid flow rate is 2 m3 / min, what is the pressure loss due to friction in a 30 m long smooth pipe? a. Reynold number = . b. Loss of Pressure = kPa.
A 300 mm x 150 mm venturimeter is provided in a vertical pipeline carrying oil of specific gravity 0.9, flowing upward. The difference in elevation of the throat section and entrance section of the venturimeter is 300 mm. The differential U – tube manometer shows a gauge deflection of 250 mm.Calculate i) The discharge of oil ii) The pressure difference between entrance and Throat section. Take : coefficient of discharge of venturimeter is 0.98
A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of 6 ft. Pressyre gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 14.5 psi) Illustrate the problem before answering the following questions: (a)determine the flow, in ft^3/s through the pipe at C neglecting all lossess. (1 bar = 14.5 psi) (b)determine the pressure in bars, recorded at C neglecting all losses.
If a dust-proofing oil at 30°C had been flowing at 0.046 m /s through a 150-mm pipe in which along-radius flow nozzle 75 mm in diameter, what would have been the deflection of the mercury? Assume C=0.98.
Freshwater at a temperature of 10°C flows at a rate of 0.10 m3/sec through the piping system sketched below, which shows the view from above. The system consists of 30 meters of 150 mm galvanized iron pipe, 4 regular 90-degree threaded elbows, and a swing check valve which may be assumed to be in the forward flow position. The elevation of Station A is 2 meters higher than Station B, zA − zB = 2 m. Calculate the following: 1. The normalized surface roughness of the pipe, ɛ / D. 2. The Reynolds number of the flow, ReD. 3. The head loss due to pipe skin friction.
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
A2 A Newtonian fluid with viscosity (Mu) flows upward at a steady rate between two parallel plates that make an angle y with the horizontal. The fluid thickness h is much smaller than the width of the channel W. The pressures at each end, P(0) and P(L), are known and the pressure variations in the y-direction are small. Assume that Vy and Vz = 0 and Vx is a function of y alone. Use the shell balance to approach : - the Total flowrate, QV
Recommend the low cost flow meter used in industries for measuring flow that provides negligible loss of head in the pipeline. Discuss its construction and working. A venturi tube of throat diameter 10 cm is placed in a pipe of diameter 20 cm. The volumetric flow rate through the venturi tube is 0.02 m3/ sec. [Given: viscosity of water = 10–3 Pas]. Determine the Reynolds number and the upstream to throat differential pressure developed.