In a process water at 30°C flows over a plate maintained at 10°C with a free stream velocity of 0.3 m/s. Determine the hydrodynamic boundary layer thickness, thermal boundary layer thickness, local and average values of friction coefficient, heat transfer coefficient and refrigeration necessary to maintain the plate temperature. Also find the values of displacement and momentum thicknesses. Consider a plate of 1 mx 1 m size.

In a process water at 30°C flows over a plate maintained at 10°C with a free stream velocity of 0.3 m/s. Determine the hydrodynamic boundary layer thickness, thermal boundary layer thickness, local and average values of friction coefficient, heat transfer coefficient and refrigeration necessary to maintain the plate temperature. Also find the values of displacement and momentum thicknesses. Consider a plate of 1 mx 1 m size.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.54P

See similar textbooks

Similar questions

Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces
Q2/ An aluminum sphere weighting 7kg and initially at a temperature of 533K is suddenly immersed in a fluid at 283K. if heat transfer coefficient between the sphere and fluid is 50W/m?.°C. Take density=2707kg/m3, specific heat=0.9KJ/kg.°C and thermal conductivity= 204W/m °C. إجابت * Determine the Bi number 0.00696 0.000696 0.0052 0.00052 0 أخری *.Determine the time required to cool sphere to 263K 26.28min 262.8min 52.56 min 525.6 min O أخری
43% uo 7:52 * ZAIN IQ I. sheet No.3.pdf Homework 01-03 -2021 one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at Te1-320°C flows in a cast iron pipe (k=80W/m.°C) whose inner and outer diameters are D =5cm, and D=5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m.°C. Heat is lost to the surroundings at T02=5°C_by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m.C. Taking the heat transfer coefficient inside the pipe to be h,=60W/m.C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. 05/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D=3.34 cm steel pipe (k=54.0W/m.°C) for the following conditions: inside and outside heat transfer coefficients are 1200W/m."C. and 2000W/m."C…
Q1: (5pt) In a cylindrical fuel element for a gas-cooled nuclear reactor, the generation rate of thermal energy within the fuel element due to fission can be approximated by the relation q(1) W/m³ %3D where a is the radius of the fuel element and is constant.The boundary surface at r = a is maintained at a uniform temperature Tɔ. (a) Assuming one-dimensional, steady-state heat flow, develop a relation for the temperature drop from the centreline to the surface of the fuel element. (b) For a radius of a = 30 mm, the thermal conductivity k = 10 W/(m °C) and qo = 2 x 107 W/m³, calculate the temperature drop from the centreline to the surface. 02: (5pt)
A perfectly stirred-and-insulated tank, initially contains 95 L oil (p-1100 kg/m, Cp31900 j/kg.C, To-5 °C). At this time, the oil is being heated by electrical energy: Q=12exp(-0.03t), where Qis rate thermal energy transferred, in kW, and t is time in minutes. How long will it take, in minutes, for the oil temperature to reach 120 °C ? Lütfen birini seçin: a.104 b.96 с. 112 d.108 e.100
Q2) Air at 20°C flows over a flat plate having a uniform heat flux of 800 W/m². The flow velocity is 4m/s and the length of the plate is 1.2 m. Determine the value of heat transfer coefficient and also the temperature of the plate as the air leaves the plate.
For a water flow over a steel surface, the temperature of water at a specific location was found to change with the vertical distance from the surface (y) up to a distance of 0.015 m as T(y) = 60 + 20y + tan(y), where temperature is in °C and y is in cm. The surface temperature and ambient temperature was measured as 60°C and 105°C, respectively. The thermal conductivity of steel and water are, respectively, 48 W/m-K and 0.6 W/m-K. What is the local convection coefficient at this location?
Air at atmospheric pressure enters a heating duct with dimensions of 3 x 6 in. The air enters the 16 ft long duct with a temperature of 32 F, and the duct surface is maintained at 150 F. If the air exit temperature is to be 68 F, what is the air flow, in lb/hr? (answer in whole number) For air, R = 53.342 ft-lbf/lbm-R, k = 0.173 Btu-in/ft2-hr-F, and cp = 0.24 Btu/lbm-
A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Convection H.T. Q3: In an industrial facility, air is to be preheated before entering a furnace by geothermal water at 120°C flowing through the tubes of a tube bank located in a duct. Air enters the duct at 20°C and 1 atm with a mean velocity of 4.5 m/s, and flows over the tubes in normal direction. The outer diameter of the tubes is 1.5 cm, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = Sr = 5 cm. There are 6 rows in the flow direction with 10 tubes in each row. Determine the rate of heat transfer per unit length of the tubes, and the pressure drop across the tube bank. For this square in-line tube bank, if the friction coefficient is 0.16. Also, the correction factor 1 for the square arrangements. Properties: (p = 1.06 kg/m', k =0.02808 W/m °C, u = 2.008x10-5 kg/m.s, Pr = 0.7202 and Cp= 1007 J/kg.K). Take C, = 0.286, C2 = 0.95 and m = 0.608. Ans. q = 23.12 kW, AP = 21 Pa]
title of the book: Engineering ThermofluidsThermodynamics, Fluid Mechanics, and Heat Transfer by Mahmoud Massoud
(heat transfer ) thanks The velocity of the fluid flowing in parallel over a 500mmx500mm flat heater surface is U= 19 m/s and the inlet velocity temperature is T_∞15 C. The surface temperature of this plate is T_s140 C, the friction force is F_D=0.4 N and the surface area of the plate is A=0.32 m2. According to this;(F_D= 0.4N A=32 m2)a) Surface shear stressb) Find the coefficient of frictionc) Heat transfer coefficientd) What is the amount of heat transfer (electric power) that must be given to maintain a constant surface temperature?