In a regenerative Rankine cycle. the closed feedwater heater with a pump as shown in the figure is arranged so that the water at state 5 is mixed with the water at state 2 to form a feedwater, which is a saturated liquid at 200 psia. Feedwater enters this heater at 350°F and 200 psia with a flow rate of 3 lbm/s. The bleed steam is taken from the turbine at 160 psia and 400°F and enters the pump as a saturated liquid at 160 psia. Determine the mass flow rate of the bleed steam required to operate this unit. Use steam tables. Feedwater Bleed steam (from turbine) [3 m m₁ The mass flow rate of the bleed steam required to operate the unit is Ibm/s.

In a regenerative Rankine cycle. the closed feedwater heater with a pump as shown in the figure is arranged so that the water at state 5 is mixed with the water at state 2 to form a feedwater, which is a saturated liquid at 200 psia. Feedwater enters this heater at 350°F and 200 psia with a flow rate of 3 lbm/s. The bleed steam is taken from the turbine at 160 psia and 400°F and enters the pump as a saturated liquid at 160 psia. Determine the mass flow rate of the bleed steam required to operate this unit. Use steam tables. Feedwater Bleed steam (from turbine) [3 m m₁ The mass flow rate of the bleed steam required to operate the unit is Ibm/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple rankine ideal cycle with water as the working fluid. Twenty kilograms of steam enters the turbine at 7.356 MPa and 500.356 oC and is cooled in the condenser at a pressure of 10.356 KPa by running cooling water from a lake through the tubes of the condenser at rate of 2000 kg. Show the T-s diagram and schematic of simple rankine cycle. For cycle determin (a) the turbine work, (b) the heat added, (c) the temperature rise of the cooling water, (d) the thermal efficiency of the cycle. For engine, determine (e) the heat added, (f) the thermal efficiency of the engine, and (g) Draw the T-s and schematic diagram.
Consider the combined gas-steam power cycle shown in attached Figure. The topping cycle is a gas-turbine cycle that has a pressure ratio of 12. Air enters the compressor at 300 K and the turbine at 1200K. The isentropic efficiency of the compressor is 80 percent, and that of the gas turbine is 85 percent.The bottoming cycle is a simple ideal Rankine cycle operating between the pressure limits of 8 MPa and50 kPa. Steam is heated in a heat exchanger by the exhaust gases to a temperature of 400°C. The exhaustgases leave the heat exchanger at 420 K. Determine (a) the ratio of the mass flow rates of the steam andthe combustion gases, (b) the total network output per kilogram of combustion gases, (c) the thermalefficiency of the combined cycle, (d) the exergy destruction associated with the process in the condenserper kilogram of combustion gases, and (e) the entropy generation associated with the process in thecombustion chamber.Use variable specific heat for ideal gas and assume a source…
A steam power plant operates on the Rankine cycle with reheat. Steam enters the high pressure turbine at a pressure of 12.5 MPa and a temperature of 550 °C, with a flow rate of 7.7 kg/s and exits at a pressure of 2 MPa. The steam is then heated to 450 ̊C at constant pressure before being expanded in the low pressure turbine and exits the condenser as a saturated liquid at 10 kPa. Since the isentropic efficiencies of the turbine and the pump are 85 percent and 90 percent, respectively; Find a) degree of dryness, b) net power, c) thermal efficiency of the cycle.
A steam power plant operates on an ideal regenerative Rankine cycle with two open feedwater heaters. Steam enters the turbine at 10 MPa and 600C and exhaust to the condenser at 5 kPa. Steam is extracted from the turbine at 0.6 and 0.2 MPa. Water leaves both feedwater heaters as a saturated liquid. The mass flow rate of steam through the boiler is 22 kg/sec. Show the cycle on a T-s diagram, and determine (a) Total power requirement of the pump in Hp, (b) Turbine power output in MW, (c) the net power output of the power plant in MW, (d) mass of steam extracted for feedwater heating in kg/sec,
Consider a steam power plant that operates on an ideal regenerative Rankine cycle and has a net power output of 150 MW. Steam enters the turbine at 10 MPa and 500°C and the condenser at 15 kPa. Steam is extracted from the turbine at 0.5 MPa to heat the feedwater in an open feedwater heater. Water leaves the feedwater heater as a saturated liquid. Show the cycle on a T-s diagram, and determine (a) the mass flow rate of steam through the boiler, and (b) the thermal efficiency of the cycle.
A steam power plant operates on an ideal regenerative Rankine cycle with two open feedwater heaters. Steam enters the turbine at 8 MPa and 550C and exhausts to the condenser at 10 kPa. Steam is extracted from the turbine at 0.6 and 0.2 MPa. Water leaves both feedwater heaters as a saturated liquid. The mass flow rate of steam through the boiler is 16 kg/s. Show the cycle on a T-s diagram, and determine (a) the net power output of the power plant and (b) the thermal efficiency of the cycle.
A steam power plant operates on a reheated Rankine cycle. Steam enters the high pressure turbine at a pressure of 12.5 MPa and a temperature of 550 ̊C, with a flow rate of 7.7 kg/s and exits at a pressure of 2 MPa. The steam is then heated to 450 C at constant pressure before being expanded in the low pressure turbine and exits the condenser as a saturated liquid at 10 kPa. Since the isentropic efficiencies of the turbine and the pump are 85 percent and 90 percent, respectively; a) degree of dryness, b) net power, c) thermal efficiency of the cycle
Steam enters the high-pressure turbine of a steam power plant that operates on the reheat Rankine cycle at 10 MPa and 550°C and leaves at 4 MPa. Steam is then reheated to 500°C before it expands to a pressure of 40 kPa. The enthalpy of steam is 3190 kJ/kg at the exit of the high-pressure turbine, and 2550 kJ/kg at the exit of the low-pressure turbine. Disregarding the pump work, the cycle efficiency is
A steam power plant operating on a regenerative cycle, as shown in the figure below, includes two feedwater heaters (CFWH and OFWH). Steam enters the turbine at 10.6 MPa and 615 (please change 16 MPa to 10.6 MPa and 600 to 615 at POINT 6). The extracted steam from each turbine must be at a pressure (at 5 MPa and 1 MPa) high enough that its saturation temperature is above that of the feedwater stream leaving the heater. The condensing steam in the heater raises the temperature of the feedwater 6. If the working fluid experiences no irreversibility as it passes through the pumps and with 85% efficiency through the turbines, determine the following: QH, QC, Wsp, WsT, and Wnet in kJ/kg
A steam power plant produces 200 MW of electric power operating on a simple ideal Rankine cycle with turbine inlet conditions of 7.5 MPa and 550 degrees Celcius and a condenser pressure of 20 kPa. The pump in the cycle can be considered ideal, while the turbine has an isentropic efficiency of 85%. The coal has a heating of 29.3 MJ/kg. Assuming that 90% of this energy is transferred to the steam in the boiler and that the electric generator has an efficiency of 96%, determine: Overall plant efficiency (ratio of net electric power output to the energy input as fuel) The required rate of coal supply
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of3 MPa and 50 kPa. The temperature of the steam at the turbine inlet is 300°C, and the massflow rate of steam through the cycle is 35 kg/s. Show the cycle on a T-s diagram with respectto saturation lines, and determine (a) the thermal efficiency of the cycle and (b) the net poweroutput of the power plant.
A gas-turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1200 kPa. The working fluid is air, which enters the compressor at 30°C at a rate of 150 m3/min and leaves the turbine at 500°C. Using constant specific heats for air and assuming a compressor isentropic efficiency of 82 percent and a turbine isentropic efficiency of 88 percent, determine (a) the net power output, (b) the work ratio, and (c) the thermal efficiency.