Refrigerant 134a is stored inside an uninsulated rigid tank (see figure below) and heated by an electric resistor for 5 minutes. How much energy is lost from the refrigerant through the tank walls during this process? Refer to the table below for properties

Refrigerant 134a is stored inside an uninsulated rigid tank (see figure below) and heated by an electric resistor for 5 minutes. How much energy is lost from the refrigerant through the tank walls during this process? Refer to the table below for properties

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are designing a piping system to facilitate the transfer of water from one industrialprocess to the next. You need the water to condense from saturated vapor to saturatedliquid at a constant 1000 kPa as it flows through the piping system. The pipe is to be madeof plain carbon steel with thermal conductivity ? = 60 W m-K⁄ and inner and outer radii?? = 5 cm and ?? = 7 cm, respectively. The thermodynamic property table at the end of thisproblem will be helpful throughout your analysis.a) If the convection coefficient between the steam and inner wall of the pipe is “verylarge”, what is the temperature of the inner pipe wall along its entire length?(Hint: Isobaric phase change is also iso___?)b) The fluid surrounding the pipe has temperature ?∞ = 30°C and the convectioncoefficient from the pipe to this fluid is ℎ = 100 W/m2⋅K. What is the heat transferrate out of the pipe, per unit meter of pipe? You may neglect radiation effects. Usea thermal resistance network in your analysis.c) The…
You want to know the power of a fan that is used to send air from a cooling system at 12 m linear distance by means of a 15 cm high stainless steel square pipe at a pressure of 105 Kpa and 25 ° C, to a ventilation port 25 m from the fan at 18 ° C at a pressure of 105 Kpa, with a flow of 0.25 m3/s (HP power
50 kg water per minute is to be heated from 30°C to 50°C by passing through a pipe of 2cm diameter. the pipe is heated by condensing the system keeping its inner surface at 100°C . find the length of pipe required. Take the following properties of water at mean bulk temperature of 40°C, density= 965 kg/m^3, v= 0.33*10^-6 m^2/sec , Cp= 4200J/kgK ,k= 0.585W/mK
⦁ 0.1 m3 rigid tank (tank volume is constant) contains water at 200ºC and 500 kPa at the beginning. Then the tank is cooled and heat loss (Q) of the system is 554.21 kJ. The final pressure (P2) of the tank is 15 kPa. During this process, determine, the final specific internal energy (u2) and the final temperature (T2) of the tank.
why did you neglect pressure at section 2? shouldn't that be taking into account when using the energy equation
The movement of 4.2 kilograms of gas through an isentropic pump requires 85 kilowatts of power. Find the power saved or increased if the process is changed to be isothermal and the Cv=0.886 kJ/kg-K and the Cp=1.758 kJ/kg-K. The final pressure is 22 psia, and the initial pressure was 850 mmHg, and the initial temperature was 38°C.
A water pump increases the water pressure from 15 psia to 80 psia. a. Determine the flow work, in Btu/lbm, required by the pump. Assume thatthe state of the water at pump inlet is saturated liquid and that the specificvolume remains constant during this process. b. Water enters this pump through a 1.5-in-diameter opening and exitsthrough a 2-in-diameter opening. Determine the velocity of the water at theinlet and outlet when the mass flow rate through the pump is 1.1 lbm/s
A piston system contains a hot fluid at 250kPa pressure that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 1500 kJ and volume is 2m3. During the cooling process, the fluid loses 400 kJ of heat, and the paddle wheel does 100 kJ of work on the fluid. At the end, volume reduces to 0.5m3. Pressure remains constant. Determine the final internal energy of the fluid. Neglect the energy stored in the paddle wheel.
A household radiator has an inlet temperature of 73.2 oC and an outlet temperature of 42.5 oC. The water flows through the radiator at a steady rate of 1×10-5 m3 s-1 and the radiator has reached a steady temperature. Given that the density of water is 1000 kg m-3 and its specific heat capacity is 4200 J kg-1 K-1, calculate the rate of heat loss (in W or J s-1) from the radiator.
Steams flow steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 450 degrees Celsius and 80 m/s, and the exit conditions are 10 kPa, 92% quality and 50 m/s. The mass flow rate of steam is 12 kg/s. Determine: a) The change in kinetic energy b) The power output c) The turbine inlet area delta ke=-1.95 kj/kg W out =10.2 MW A in =0.00447 m2
A fluid, contained in a horizontal cylinder fitted with a frictionless leak proof piston, is continuously agitated by means of a stirrer passing through the cylinder cover. The cylinder diameter is 0.40 m. During the stirring process lasting 10 minutes, the piston slowly moves out a distance of 0.485 m against the atmosphere. The net work done by the fluid during the process is 2 kJ. The speed of the electric motor drivingthe stirrer is 840 rpm. Determine the torque in the shaft and the poweroutput of the motor.
17. A fully inflated tire has a volume of 15 ft3. The pressure and temperature of theair in the tire are 65 psia and 75 F, respectively. At this condition, the air intakeneedle is depressed for 3 s and then released. Treating air as an ideal gas and assumingsmall changes in the tire temperature and volume, Find the amount of air that leftthe tire. Assume a discharge coefficient of 0.61 and a flow area of 0.01 in2.