In a rolling operation, a plate of 2 cm thick and 25 cm wide is passed through a rolling mill having 2 powered rolls. Assume friction was enough for rolling. Thickness of the plate at the end of operation is 1.7 cm. Each roll has a radius of 0.3 m and a roll speed of 0.5 revolution per second. Flow curve has the following values K 225 MPa and n = 0.15. Determine the power required for driving the rolls. =

In a rolling operation, a plate of 2 cm thick and 25 cm wide is passed through a rolling mill having 2 powered rolls. Assume friction was enough for rolling. Thickness of the plate at the end of operation is 1.7 cm. Each roll has a radius of 0.3 m and a roll speed of 0.5 revolution per second. Flow curve has the following values K 225 MPa and n = 0.15. Determine the power required for driving the rolls. =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The maximum possible draft in rolling which is the difference between initial and final thickness of the sheet metal, depends on A. Rolling force B. Roll radius C. Roll width D. Yield shear stress of the material
In a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.
1. The friction in direct extrusion is ________ Indirect extrusion. a) Greater than. b) Equal to. c) Less than.2. The Temperature in hot forming process is ____. a) (0 to 0.4) Tm. b) (0.5 to 0.75) Tm. c) 0.9 Tm. d) 0.4 Tm. e) 0.8 Tm. f) (0.3 to 0.5) Tm. Where Tm is the melting temperature of the work piece.3. Maximum draft in rolling depends on _______. a) Coefficient of friction and roll radius. b) Thickness of plate. c) Smoothness of roll Surface. d) Roll rotational speed.e) Width of the plate. f) Length of the plate.4. In deep drawing process, the drawing ratio (DR) has a higher limit (value) of:- a) 6. b) 1. c) 4. d) 5. e) 7. f) 2. g) Zero.5. Spring Back is a phenomena usually associated with which of the following processes:-a) Extrusion. b) Forging. c) Bending. d) Wire drawing. e) Rolling. f) Sheet metal cutting. g) Deep Drawing.
A mechanical press is powered by a 23-kW motor and operates at 40 strokes per minute. It uses a flywheel, so that the crankshaft speed does not vary appreciably during the stroke. If the stroke is 150 mm, what is the maxumum const.ant force rhat can be exerted over the entire stroke length?
In a slab rolling operation, the maximum thickness reduction (del hmax) is given by del hmax = μ²R, where R is the radius of the roll and u is the coefficient of friction between the roll and the sheet. If µ = 0.1, find the maximum angle subtended by the deformation zone at the centre of the roll.
m) The method of sheet forming in which springback is prevented is called ..........n) With the help of liquid pressure of tubular parts with complex surface geometryThe method used in shaping is called ..............o) The rounding of the two ends of the sheet metal produced in rolling ...........is the error that occurs.
A tube of 12 mm external diameter and 1mm thickness is to be reduced to 16 mm external diameter and 0.5 mm thickness. The die angle is 24º and plug angle is 16º. The coefficients of friction at die and tube interface and tube and plug (mandrel) interface is 0.5. The flow stress of tube material is 340 N/mm2 . The tube drawing is carried at a speed of 0.4 m/s. Calculate the fixed plug
A 10 mm thick plate is rolled to 7 mm thick in a rolling mill using 1000 mm diameter rigid rolls. The neutral point is located at an angle of 0.3 times the bite angle from the exit. What will be the thickness of the plate at the neutral point.
In a single pass rolling process using 412mm diameter steel rollers, strip of width 120mm and thickness 8mm undergoes 10%reduction of thickness. The angle of bite in radians is.
How can we find the value of shear flow?
Question 3A rolling operation on a 250 mm wide, 8 mm thick, 1112 cold rolled steel takes place using hardened steel rolls with a surface finish of 0.03 μm. The rolls have a diameter of 350 mm and rotates at 115 rpm. The final thickness of the plate is 6 mm and the entry speed of the plate is 1.8m/s Calculate: 3.1)The minimum coefficient of friction required, that will make the rolling operation possible. 3.2 The required roll force. 3.3 The position of the neutral point, ??3.4 Indicate, using a sketch, the neutral point showing all relevant notation and dimensions
Does the shear flow vary linearly along with segments that areperpendicular to the direction of shear?