In a steam turbine installation running on ideal Rankine cycle steam leaves the boiler at 10 MPa and 700°C and leaves turbine at 0.005 MPa. For the 50 MW output of the plant and cooling water entering and leaving condenser at 15°C and 30°C respectively determine, (a) the mass flow rate of steam in kg/s (b) the mass flow rate of condenser cooling water in kg/s c) the thermal efficiency of cycle d) the ratio of heat supplied and rejected (in boiler and condenser

In a steam turbine installation running on ideal Rankine cycle steam leaves the boiler at 10 MPa and 700°C and leaves turbine at 0.005 MPa. For the 50 MW output of the plant and cooling water entering and leaving condenser at 15°C and 30°C respectively determine, (a) the mass flow rate of steam in kg/s (b) the mass flow rate of condenser cooling water in kg/s c) the thermal efficiency of cycle d) the ratio of heat supplied and rejected (in boiler and condenser

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5400 kPa, the reheat section 1100 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 94 %. Determine the following values. (1) The specific enthalpy at the exit of the high-pressure turbine. (2) The specific entropy at the exit of the high-pressure turbine. (3) The temperature at the inlet of the high-pressure turbine. (4) The temperature at the inlet of the low-pressure turbine. (5) The thermal efficiency of the cycle.
Steam enters the high-pressure turbine of a steam power plant that operates on the reheat Rankine cycle at 10 MPa and 550°C and leaves at 4 MPa. Steam is then reheated to 500°C before it expands to a pressure of 40 kPa. The enthalpy of steam is 3190 kJ/kg at the exit of the high-pressure turbine, and 2550 kJ/kg at the exit of the low-pressure turbine. Disregarding the pump work, the cycle efficiency is
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Assuming an isentropic efficiency of 85 percent for both the turbine and the pump, determine: the quality of the steam at the turbine exit the thermal efficiency of the cycle specific enthalpy (kJ/kg) at the condenser both inlet and outlet specific enthalpy (kJ/kg) at the boiler both inlet and outlet WT, WP, WNet(kJ/kg) actual Qin (kJ/kg) and actual Qout (kJ/kg).
Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 623 K and is condensed in the condenser at a pressure of 10 kPa. Determine (i) the thermal efficiency of this power plant, (ii) the thermal efficiency if steam is superheated to 873 K instead of 623 K, and (iii) the thermal efficiency if the boiler pressure is raised to 15 MPa while the turbine inlet temperature is maintained at 873 K.
Consider a 175 MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 575°C and is cooled in the condenser at a pressure of 10 kPa. 1. Show the cycle on a T-s diagram with respect to saturation lines. Determine: 2. the quality of the steam at the turbine exit, 3. the thermal efficiency of the cycle, and 4. the mass flow rate of the steam.
Consider a steam power plant with a reheat Rankine cycle. The steam enters the high pressure turbine at 16 MPa and 550 ° C, and condenses in the condenser at 10 kPa. If the moisture content of the steam at the outlet of the low pressure turbine should not exceed 5%, determine: a) The pressure to which the steam should be reheated. b) The thermal efficiency of the cycle
(simple cycle)Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respect to saturation lines and determine (a) the quality of the steam at the turbine exit, (b) the thermal efficiency of the cycle, and (c) the mass flow rate of the steam.
Thermodynamics 2 Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 91 MW. Steam enters the high-pressure turbine at 10 MPa and 500 C and the low-pressure turbine at 1 MPa and 500 C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. The isentropic efficiency of the turbine is 95 percent, and that of the pump is 90 percent. The required power input in the pump in MW.
Consider a 250-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 525°C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respect to sat¬uration lines, and determine:(a) the quality of the steam at the turbine exit, (b) the thermal efficiency of the cycle, and(c) the mass flow rate of the steam.
Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 10 kPa. Determine the thermal efficiency of this power plant, the thermal efficiency if steam is superheated to 600°C instead of 350°C, and the thermal efficiency if the boiler pressure is raised to 15 MPa while the turbine inlet temperature is maintained at 600°C. Draw the T-S diagram of each condition.
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Assuming an isentropic efficiency of 85 percent for both the turbine and the pump, determine the quality ofthe steam at the turbine exit, the thermal efficiency of the cycle, specific enthalpy (kJ/kg) at the condenser, and actual Qin (kJ/kg).
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the quality of the steam at the turbine exit, (b) the thermal efficiency of the cycle, and (c) the mass flow rate of the steam.