In a transistor, Ic = 100 mA and If = 100.2 mA. The value of ß is . 1. 100 2. 50 3. about 1 4. 200 In a transistor if ß = 100 and collector current is 10 mA, then Ig is 1. 100 mA 2. 100.1 mA 3. 110 mA 4. none of the above The relation between B and a is 1. B= 1/ (1 – a ) 2. β- (1-α )/α 3. β α/(1 -α) 4. β-α/(1 +α) As the temperature of a transistor goes up, the base-emitter resistance %3D 5. decreases 6. increases 7. remains the same 8. none of the above

In a transistor, Ic = 100 mA and If = 100.2 mA. The value of ß is . 1. 100 2. 50 3. about 1 4. 200 In a transistor if ß = 100 and collector current is 10 mA, then Ig is 1. 100 mA 2. 100.1 mA 3. 110 mA 4. none of the above The relation between B and a is 1. B= 1/ (1 – a ) 2. β- (1-α )/α 3. β α/(1 -α) 4. β-α/(1 +α) As the temperature of a transistor goes up, the base-emitter resistance %3D 5. decreases 6. increases 7. remains the same 8. none of the above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume you are to create n+pn transistor using n- and p-typed doped silicon with the following doping concentrations, 3 1018 /cm3, 6.8/cm3, and 5 1016/cm3, for emitter, base and collector regions, respectively. You also know Ln = 10 μm, Lp = 4 μm, μn = 1600 cm2/Vs, μp = 600 cm2/Vs, ni = 1,5 1010 1/cm3, q = 1,602 10-19 C, er = 12, eo = 8,85 10-12 F/m, VT = 25 mV. What is the minimum VCE for operation in active mode assuming hFE = β is very large?
The DC load line and point Q of the circuit in figure (a) are shown in figure (b).For the BJT, silicon, β = 120. Find the values of RE, R1, and R2 such that the circuit has stable polarization.
A certain npn silicon transistor has vBE=0.7 V for iB=0.1 mA at a temperature of 30°C. Sketch the input characteristic to scale at 30°C. What is the approximate value of vBE for iB = 0.1 mA at 180°C? (Use the rule of thumb that vBE is reduced in magnitude by 2 mV per degree increase in temperature.) Sketch the input characteristic to scale at 180°C.
For an NPN Bipolar Junction Transistor base-emitter voltage, VBE is 0.7 V at collector current,Ic of 1mA. Calculate the saturation current, emitter-base voltage, emitter current whencollector current is (X+2) mA. Assume β =100 and T=300 K for your calculation.
Using IC that is approximately equal to IE. Determine the value of emitter voltage VE, when VCC=19V, RC=2500 ohms, RE=228 ohms, VC=6 V and R2=5894ohm
Determine the range of changes in VBE at T = 25℃ for the range 0.2 ≤ iC≤ 5 mA, given that VBE = 0.7 V and iC = 1.2 mA in NPN transistor.
For the transistor , IS = 6 × 10−16 μA, βF = 100, and βR = 0.25. (a) Labelthe collector, base, and emitter terminals of thetransistor. (b) What is the transistor type? (c) Labelthe base-emitter and base-collector voltages, VBEand VBC, and the normal directions for IE , IC, andIB. (d) Find the values of IE , IC, IB, VBC, and VBEif I = 175 μA.
Figure 1 shows the transfer curve of a network with an unknown channel Junction Field Effect Transistor (JFET). (i) Identify the channel of the JFET; justify your answer. (ii) Given the supply voltage of 16 ?, design a voltage divider network using the JFET in (i) above. Take ?1 = 1400??; ?2 = 180??; and ?? = 10 ?. Please use the nearest standard resistor values. (iii) With the obtained standard resistance values in (ii) above, determine the new ??? and ????, using the mathematical approach only.
P-channel MOSFET with heavily doped P-type poly-Si gate has a threshold voltage of -I. S Y with V sb = 0 V. When a 5 V reverse bias is applied to the substrate. the threshold voltage changes to 2.3 V. (a) What is the dopant concentration in the substrate if the oxide thickness is 100 nm? (b) What is the threshold voltage if Vsb is 2.5 V?
For the NMOSFET, K=2mA/V^2 and V_THN = 1V. Determine the current I_R
How can I determine the value of beta of a transistor, specifically for 2n2218 transistor. I've been told to look for the datasheet but where exactly do I look for in the datasheet to know the beta? TYIA
The values of the capacitors used in the circuit created by using cascode silicon transistors are sufficiently large and given as B1 = 100, B2 = 120. find: a) Ib1,Ib2,Ic2,Ic1,Ie1 current values? b)Vc2,Vc1,Ve1 voltage value ? c)for what purpose is this circuit used?