In a zero gravity region, a drop of a liquid of surface tension o assumes a cylindrical shape of diameter D between two parallel glass plates that are a distance d apart. If curved surface of the drop is at right angles to the plates as shown in the figure, find force exerted by the drop on a plate. T6D (inwards)

In a zero gravity region, a drop of a liquid of surface tension o assumes a cylindrical shape of diameter D between two parallel glass plates that are a distance d apart. If curved surface of the drop is at right angles to the plates as shown in the figure, find force exerted by the drop on a plate. T6D (inwards)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
The 100cm radius cylinder weighs 3.1 KN and rest on the bottom of a container which is 1.5 meter long. Oil and water are poured into the left and right portion of the container to the depth of 0.8m and 1.4m respectively. Find the magnitude of the horizontal and vertical components of the force which will keep the cylinder touching the container at B.
To what height will 68˚F ethyl alcohol rise in a 0.005 in internal diameter glass capillary tube? The density of the alcohol is 49 lbm/ft3 note ? = 0.00156 ???/ ?? and ? = 0°.
An open settling tank shown in the figure contains a liquid suspension. Determine the resultant force acting on the gate and its line of action if the liquid density is 850 kg/m3. The gate is parabolic as sketched, looking straight at the gate
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
A cylindrical disk ofwood weighing 45.0 N and having adiameter of 30.0 cm floats on a cylinderof oil of density 0.850 g /cm3(Fig.). The cylinder of oilis 75.0 cm deep and has a diameterthe same as that of the wood.(a) What is the gauge pressure at thetop of the oil column? (b) Supposenow that someone puts a weightof 83.0 N on top of the wood, butno oil seeps around the edge of thewood. What is the change in pressureat (i) the bottom of the oil and(ii) halfway down in the oil?
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.
Gate ABC is a circular arc, sometimes called a Tainter gate ,which can be raised and lowered by pivoting about point O .See Fig.. For the position shown, determine ( a ) thehydrostatic force of the water on the gate and ( b ) its line ofaction. Does the force pass through point O ?
Two small vessels are connected to a U-tube manometercontaining mercury(relative density 13.56) and the connectingtubes are filled with alcohol (relative density 0.82). Thevessel at the higher pressure is 2 m lower in elevation than theother. What is the pressure difference between the vessels whenthe steady difference in level of themercury menisci is 225 mm?What is the difference of piezometric head? If an inverted U-tubemanometer containing a liquid of relative density 0.74 wereused instead, whatwould be the manometer reading for thesame pressure difference?