In an aluminum pot, 0.796 kg of water at 100 °C boils away in four minutes. The bottom of the pot is 1.03 × 10-³ m thick and has a surface area of 0.0294 m². To prevent the water from boiling too rapidly, a stainless steel plate has been placed between the pot and the heating element. The plate is 2.67 x 10-3 m thick, and its area matches that of the pot. Assuming that heat is conducted into the water only through the bottom of the pot, find the temperature in degrees Celsius at the steel surface in contact with the heating element. Number i Units <>

In an aluminum pot, 0.796 kg of water at 100 °C boils away in four minutes. The bottom of the pot is 1.03 × 10-³ m thick and has a surface area of 0.0294 m². To prevent the water from boiling too rapidly, a stainless steel plate has been placed between the pot and the heating element. The plate is 2.67 x 10-3 m thick, and its area matches that of the pot. Assuming that heat is conducted into the water only through the bottom of the pot, find the temperature in degrees Celsius at the steel surface in contact with the heating element. Number i Units <>

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is to be boiled at sea level in a 30-cm-diameter stainless steel pan placed on top of a 3-kW electric burner.If 51 percent of the heat generated by the burner is transferred to the water during boiling, determine the rate of evaporation of water. Please give your answer in kg/hour.
Water in a 5-cm-deep pan is observed to boil at 98°C. At what temperature will the water in a 40-cm-deep pan boil? Assume both pans are full of water.
The specific volume of water at 30 psia and 250.34 F (saturation) is 0.017004 cubic feet per pound mass. How much heat in Btu/hr must be added to evaporate the water at the rate of 10 gal/hour if the latent heat of vaporization is 945.9 Btu per pound mass
Saturated refrigerant-134a vapor at 34°C is to be condensed as it flows in a 1-cm-diameter tube at a rate of 0.1 kg/min. Determine the rate of heat transfer from the refrigerant. What would your answer be if the condensed refrigerant is cooled to 20°C?
Water vapour at 100 kPa and 150 ℃ is contained in a rigid vessel. At what temperature will the vapour stat to condense when the container is cooled slowly? How much heat will have to be removed per kilogram in this cooling process?
Saturated steam coming off the turbine of a steam power plant at 40°C condenses on the outside of a 3-cm-outerdiameter, 35-m-long tube at a rate of 70 kg/h. Determine the rate of heat transfer from the steam to the cooling water flowing through the pipe.
Consider a pan of water being heated by placing a heating element in the water. Which method is a more efficient way of heating water? Explain.
The average atmospheric pressure in Denver (elevation = 1610 m) is 83.4 kPa. Determine the temperature at which water in an uncovered pan boils in Denver.
Water is boiled at atmospheric pressure by a horizontal polished copper heating element of diameter D = 5 mm and emissivity ε = 0.05 immersed in water. If the surface temperature of the heating wire is 350°C, determine the rate of heat transfer from the wire to the water per unit length of the wire. The properties of water at the saturation temperature of 100°C are ρl= 957.9 kg/m3 , hfg = 2257.0×10^3J/kg, The properties of vapor at the film temperature ρv = 0.441 kg/m3 , µv = 1.73 × 10^-5 kg m/s , Cpv= 1977 J/kg °C, kv = = 0.0357 W/m °C Select one: a. 853 W b. 933 W c. 707 W d. 1953 W
Water is being heated in a vertical piston–cylinder device. The piston has a mass of 40 kg and a cross-sectional area of 150 cm2. If the local atmospheric pressure is 100 kPa. Determine the temperature at which the water starts boiling.
Water is boiled at atmospheric pressure by a horizontal polished copper heating element of diameter D = 5 mm and emissivity ε = 0.05 immersed in water. If the surface temperature of the heating wire is 350°C, determine the heat flux from the wire to the water. The properties of water at the saturation temperature of 100°C are ρl= 957.9 kg/m3 , hfg = 2257.0×10^3J/kg, The properties of vapor at the film temperature ρv = 0.441 kg/m3 , µv = 1.73 × 10^-5 kg m/s , Cpv= 1977 J/kg °C, kv = = 0.0357 W/m °C Select one: a. 5.94 × 104 W/m2 b. 7.94 × 104 W/m2 c. 3.94 × 104 W/m2 d. 1.94 × 104 W/m2
If 10kg of water at 920kPa pressure and at 600C is heated to boiling point, then to dry saturated steam and then to superheated steam at a temperature of 2100C, determine: The sensible heat and latent heat