QuestionA thin plank of mass M is placed centrally across two solid cylindrical rollers eachof mass m, and the system is allowed to move freely from rest without slip downslope of angle 9 as shown in the figure below.(a) Derive expressions for the initial accelerations of the plank and the roller.Your solution should include the following in a systematic way:(i) Identification of the types of ensuing motions of the plank andthe rollers,(ii) free-body, kinematic and kinetic diagrams with an appropriateglobal axes system clearly shown,(iii) statements of relevant kinematic and kinetic relationships withreference to your chosen global axes system in (ii), and+

Given-Information:- Mass of Plank, MMass of Two Rollers, mSlope of angle, θ To-Determine:- Derive…

Answered: suing motions of the plank

Engineering

Mechanical Engineering

suing motions of the plank

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spool of mass 60 kg is supported on two rollers at A and B as shown in FigureQ1(c). Neglect the mass of the inelastic cable, friction and the mass of therollers at A and B. Knowing that a constant pulling force P is applied in order tounwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spoolis (604) mm, Appendix Ashows the examples of identifying the radius of gyration using student ID.(i) Determine the angular acceleration of the spool. (ii) Determine the pulling force P. (iii) Explain with calculation on ways to increase the acceleration of cablebeing pulled. [
A min cage of mass 4t is to be raised with an acceleration of 1.5m/s2 by a cable passing over a hoist drum of 1.5m diameter. What is the power required when the load has reached a velocity of 6m/s, neglecting the inertia of the drum and weight of the cable, but allowing for bearing friction torque of 3kN at the drum? What is the power required at a uniform velocity of 6m/s
The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees a) draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *****MASS IS 10KGS NOT 10LBS*****
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Korean Bell. A bell-ringer hits a massive bell using a 21-kg cylindrical log. The log is supported by two cords that behave like a rod. He normally uses a 200-N force P, at 60° with respectto the log, to push the log towards the bell. Assuming the two supports have negligible mass, determine the (a) normal and tangential accelerations of the log, and the (b) force developed at each support, at the instant when the cords are vertical and the angular velocity of the log is ω = 6 rad/s, CW. *kindly, include all necessary FBDs and solutions*if necessary, use g=9.81 m/s2
A Mine cage of mass 4t is to be raised with an acceleration of 1.5 m/s by a rope passing over a hoist drum of 1.5 m diameter. What is the power required when the load has reached a velocity of 6 m/s, neglecting the inertia of of the drum and the weight of the rope, but allowing for a bearing friction torque of 3kN m at the drum. What is the power required at a uniform velocity of 6 m/s
The slender rod shown in Fig 1 has a mass m and length L and is released from rest when θ =0°. Determine the horizontal and vertical components of force which the pin at A exerts on therod at the instant θ = 90°. Use normal and tangent coordinates, assume weight in center of rod, from kinematics, we found ω2 = 3g/L
A uniform, 0.0300 kg rod of length 0.400 m rotates in ahorizontal plane about a fixed axis through its center and perpendicularto the rod. Two small rings, each with mass 0.0200 kg, are mounted sothat they can slide without friction along the rod. They are initially heldby catches at positions 0.0500 m on each side of the center of the rod,and the system is rotating at 48.0 rev/min. With no other changes in thesystem, the catches are released, and the rings slide outward along therod and fly off at the ends. What is the angular speed (a) of the systemat the instant when the rings reach the ends of the rod; (b) of the rodafter the rings leave it?
The gear train shown operates in a horizontal plane and is used to transmit motion to the rack D of mass mD = 4.9 kg. If an input torque M = 63 N●m is applied to gear A, what will be the magnitude of the resulting acceleration a of the unloaded rack? (The mechanism which it normally drives has been disengaged.) Gear C is keyed to the same shaft as gear B. Gears A, B, and C have pitch diameters dA = 185 mm, dB = 355 mm, and dC = 185 mm, and centroidal mass moments of inertia IA = 0.45 kg●m2, IB = 3.38 kg●m2, and IC = 0.45 kg●m2, respectively. All friction is negligible.
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A uniform cylindrical turntable of radius 1.9 m and mass 30.0kg rotates counterclockwise in a horizontal plane with an initial angular speed of 4pi rad/s. The fixed turntable bearing is frictionless. A lump of clay of mass 2.25kg and negligible size is dropped onto the turntable from a small distance above it and immediately sticks to the turntable at a point 1.80m to the east of the axis. A. Find the final angular speed of the clay and turntable. B. Is the mechanical energy of the turntable-clay system constant in this process? C. Is the momentum of the system constant in this process? Explain your answer.
A 20kg slender rod AB is pinned to a roller at A that slides freely along the slot as shown in the figure below. The rod is released from the rest at an angle of 30. At the same time, a couple moment of M = 5 N.m in clockwise direction is applied at its centre of gravity. If immediately after the release the acceleration of the roller at A is 43m/s, determine the reaction forces at the pin connection at Point A.