In an experiment to determine the concentration of H2SO4 in a brand of toilet cleanser, 10.0 cm3 of the cleanser was first diluted to 250.0 cm3 with distilled water. 25.0 cm3 of the diluted cleanser were titrated with 0.320 mol dm–3 NaOH solution, using methyl orange as indicator.If 29.2 cm3 of NaOH solution is used, what is the concentration of H2SO4 in the undiluted toilet cleanser? a. 2.30 mol dm–3 b. 4.60 mol dm–3 c. 9.20 mol dm–3 d. 11.50 mol dm–3

In an experiment to determine the concentration of H2SO4 in a brand of toilet cleanser, 10.0 cm3 of the cleanser was first diluted to 250.0 cm3 with distilled water. 25.0 cm3 of the diluted cleanser were titrated with 0.320 mol dm–3 NaOH solution, using methyl orange as indicator.If 29.2 cm3 of NaOH solution is used, what is the concentration of H2SO4 in the undiluted toilet cleanser? a. 2.30 mol dm–3 b. 4.60 mol dm–3 c. 9.20 mol dm–3 d. 11.50 mol dm–3

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter13: Titrations In Analytical Chemistry

Section: Chapter Questions

Problem 13.5QAP

See similar textbooks

Similar questions

As part of the analysis of water samples, the hardness of water is commonly measured and calculated. It is commonly expressed in ppm by mass (parts per million) of CaCO3. Parts per million is also equivalent to milligrams of CACO3 per liter of water. In a sample taken by an environmentalist, he was able to observe a hardness count of 205 mg CacO3/L. Given this hardness count of the sample, what is the molar concentration of Ca2+ ions in the water sample?
The solubility of borax, which is made up of sodium tetraborate (Na2B4O5(OH)4 8H2O), was analyzed. The dissolution of borax is: Na2B4O5(OH)4 • 8H2O(s) ⇌ 2 Na+(aq) + B4O5(OH)42–(aq) + 8 H2O(l) A 50 mL saturated solution was prepared. After filtration of solution, 5 mL aliquot was transferred to a flask and titrated using 0.432 M HCl. The endpoint was found to be 4.73 mL of the titrant. Tetraborate anion (B4O5(OH)42-) is a weak base which reacts with HCl like the following reaction: B4O5(OH)42–(aq) + 2 H+(aq) + 3 H2O(l) ⇌ 4 H3BO3(aq) What is Ksp expression for the dissolution? What is the tetraborate ions concentration in the filtrate? What is the molar solubility and Ksp of borax if the titration was done at room temperature (298 K)?
You have a solution that contains acetic acid, (CH3COOH or HAc). The concentration of acetic acid in the aqueous solution is 0.35 mol / dm3. Ka = 1.7378 x 10 ^ -5 M a. Calculate the pH of the solution. 15 cm 3 of the acetic acid solution was titrated with sodium hydroxide solution, NaOH (aq), at a concentration of 0.5 mol / dm3 b. Describe how you would proceed to perform a titration of an acid of unknown concentration. What information can be obtained from a titration, describe the different phases. c. How much NaOH will be added when the equivalence point occurs?
Please explain how the relationship S = 0.330(Ksp)^(1/5) was derivedto calculate the solubility (S) of cerium(IV) ions in a saturated solution of cerium(IV) fluoride, CeF4.
If 25,0 cm3 of the NH3 (concentration 0,10 mol∙dm–3) is titrated with the HCl (concentration 0,050 mol∙dm–3), calculate the pH at the equivalence point of the titration
The precipitation of Al(OH)3 (Ksp = 1.3 x 10-33) is sometimesused to purify water. (a) Estimate the pH at whichprecipitation of Al(OH)3 will begin if 5.0 lb of Al2(SO4)3is added to 2000 gal of water. (b) Approximately howmany pounds of CaO must be added to the water toachieve this pH?
The limiting molar conductivities of KCl, KNO3, and AgNO3 are 14.99 × 10-3 S m2 mol-1, 14.50 × 10-3 S m2 mol-1, and 13.34× 10-3 S m2 mol-1, respectively (all at 25°C). What is the limiting molar conductivity of AgCl at this temperature?
Calculate the % relative error in solubility by using concentrations instead of activitiesfor Fe(OH)2 in 0.0500 M KNO3 (give the source for thermodynamic solubility).
Consider the titration illustrated in Figure 8.] Anhydrous sodium carbonate (Na₂CO₃) is a primary standard. When 0.364 grams of the substance is placed in a conical flask, then 20.00 cm³ of sulphuric acid (H₂SO₄) solution is required to reach the end point of the titration. What is the concentration in mol·dm⁻³ of the sulphuric acid solution? [Give the answer to 3 decimal places. Do not type in the unit. Use a decimal point.] *
What wt of magnetite should be taken for analysis in order that after converting to a precipitate of Fe2O3.xH2O, the percentage of Fe3O4 in the sample can be found by multiplying the wt in grams of the ignited precipitate (Fe2O3) by 100.
An impure sample of calcium carbonate with a mass of 7.95 g was reacted with 50.00 cm3 of 1.00 mol dm hydrochloric acid (an excess). The resulling solution was transferred to a volumetric flask and titrated with 11.10cm3 of 0.300 mol dm-3 sodium hydroxide solution. Determine the percentage purity by mass of the calcium carbonate sample.CaCO3 + HCl -> CaCl2 + H2O + CO2 HCl + NaOH -> NaCl +H2O a. Determine how many moles of hydrochloric acid were used.b. Determine how many moles of excess HCI was titratedc. Determine how much in moles calcium carbonate present in the sample.d. Calculate the mass of calcium carbonate presente. Determine the percentwge calcium carbonate is in the sample.
Potassium acid phthalate, KHC8H4O4 ( MM=204.2 ), reacts with sodium hydroxide on a 1:1 molar basis. A sample of the acid weighing 0.4823 g was titrated with NaOH, requiring 24.35 mL to reach the endpoint. Calculate the molar concentration of the sodium hydroxide solution.